Bedienungsanleitung Ferm FPCS 1800 (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

110288

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Ferm

Before using the circular saw

Check the following points:

Is the saw blade missing any teeth or showing •

any cracks, it so must be replaced

immediately.

Make sure the blade is secure.•

Use this circular saw to saw only wood, wood-•

like products.

Do not use circular saw blades which are •

deformed or damaged.

Do not use HSS blades.•

Only use blades meeting the required •

dimensions, as well as data and descriptions;

Do not stop the blade of a circular saw by •

pressing the blade from the side.

Check that the blade guard can freely move •

and fully closes.

Never lock-up the guard in the open position.•

Never put sideward pressure on the blade. •

This may cause the blade to break.

Be careful when cutting wood with knots, nails •

or cracks in it and/or dirt on it, as these

can cause the blade to get stuck.•

Never leave the circular saw unattended.•

Use this circular saw to saw only wood or •

wood-like products.

Using circular saw.

Use clamps or a vice to hold the work.•

Never remove wood chips and saw dust that is •

close to the saw blade with your hands. If

there are small pieces of wood left between

the fixed and the movable parts, the circular

saw will have to be stopped. The plug needs

to be removed from the socket,

before any left piece can be removed.•

Check that the blade is suitable for the spindle •

speed of the circular saw. Do not attempt to

cut before the circular saw has reached full

speed. Make sure the circular saw runs

without load (i.e. is not in contact with the

work) when you switch it on. The circular saw

must have reached its full speed first.

Never cut wood that is thicker than the depth •

of the saw blade.

When cutting in wooden walls or floors, check •

there is no wiring or piping where you intend to

cut.

Switch off the tool and wait until the blade has •

stopped completely before moving the

saw away from the work or putting it down. •

Hearing protection should be worn when

Safety tips for the laser beamer

Never look into the light beam of the laser.•

Never point the light beam of the laser at •

humans or animals.

Do not point the light beam of the laser at •

strongly reflecting material. Hazard from

reflected light.•

Only have repairs made to the laser beamer •

by qualified personnel / professional repair

specialists.•

Do not insert any hard objects into the laser •

optics.

Clean the laser optics with a soft, dry brush.•

Switch off the machine immediately when you

discover:

A defective switch.•

Overheating of the circular saw.•

Smoke or odour caused by scorched •

insulation.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Setting the sawing angle (bevel)

Fig. B

Loosen the saw angle clamping knob (11).•

Rotate the soleplate (6) in the correct position •

(0º - 50º) and tighten the saw angle clamping

knob. The sawing angle (bevel) can be read

on the protractor (10).

Fitting the rip fence

Fig. C

Loosen the rip fence clamping knob (12).•

Insert the rip fence into the slots provided.•

Set the correct cut width and thighten the rip •

fence clamping knob (12).

Setting the cutting depth

Fig. D

Pull out and loosen the cut depth clamping •

knob by turning it counter clockwise (16).

Caution! Do not turn the cut clamping

knob more than 1 full turn.

Move the soleplate (6) downwards.•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FPCS 1800 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info