Bedienungsanleitung Ferm fpjs 1800lk jsm1019 (Seite 8 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

383527

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

8 Ferm

Adjusting the bottom plate

Fig. C + D

Adjust the angle of the bottom plate as follows:

A. Loosen the socket head screws with the Allen

key supplied.

B. Turn the bottom plate to the right or left in the

desired sawing angle.

You can read this on the protractor. The

maximum sawing angle is 45º.

C. Tighten the socket head screws again.

Connecting and removing the battery

Fig. A + E

Insert the battery into the base of the •

appliance, as shown on the illustration. Push

the battery until it latches in.

Press the locking button (4) on either side •

before removing the battery, and disengage

the battery from the base of the appliance.

Only use batteries of the following type.

Using any other batteries could cause

serious injury or damage the tool.

CDA1051: FPB-1800L, 18V Lithium-Ion.

CDA1053: FPB-1800N, 18V NiMH.

The following charger can be used to

charge these batteries.

CDA1052: FPL-1800 (Lithium-Ion and NiMH).

CDA1054: FPL-1800N (NiMH only).

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Switching on and off

This machine is equipped with a safety switch.•

Start the machine by pressing the “lock off” •

button (to disengage the switch) and switch on

the machine.

Release the (On/Off) switch to switch the •

machine off.

Speed control

Fig. A

The speed of the saw blade can be controlled with

the rotary knob at the top of the jig saw.

The higher the position, the higher the speed.

The highest position is 6. The ideal sawing speed

will depend on the profile and the tooth of the saw

blade and on the material you want to saw. For

soft materials, select a reasonably high speed and

a coarse tooth. If you want to saw hard materials,

select a lower speed and a fine tooth.

Pendulum setting

Fig. F

For an optimum sawing result you must set the

way in which the teeth of the saw blade

grip the material. You do this by adjusting the

pendulum (8).

Soft material (wood, plastics etc.): set the •

pendulum to level II or III. For a sharp saw cut,

use pendulum level 0 or I.

Medium-hard material (hardwood, aluminium •

etc.): set the pendulum depending on the

application. For thin material use pendulum

level 0, or I if you are working with rasps or

knives.

Hard material (steel etc.): set the pendulum to •

level 0.

Curves: set pendulum to level 0.•

You can adjust the pendulum level while the

appliance is in operation.

Guard

Fig. A

The jig saw is fitted with a guard (10). Make sure

that this guard is always mounted correctly while

the jig saw is in use.

Sawing

Switch on the jig saw.•

Place the bottom plate of the appliance on the •

work piece.

Move slowly towards the previously drawn •

sawing line and press the jig saw forward

slowly. Press the bottom plate firmly against

the work piece. If you do not do this the jig saw

is likely to vibrate and the saw blade will break.

Let the jig saw do the work. Do not press

too hard on the jig saw.

Cutting in

Fig. G

If the starting position of the work piece to be sawn

is not the side, or if no hole has been drilled, you

must cut in. To do this, proceed as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm fpjs 1800lk jsm1019 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info