Bedienungsanleitung Ferm GRM1010 (Seite 7 von 12) (Englisch)

763656

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Ferm

running unattended or unused for more than 3

minutes.

• When the machine is running, please maintain

a constant water supply. Without water

circulation will damage the sealing rings of the

machine.

• It is necessary to turn on the spray lance within

one or two minutes after the machine has been

started. Otherwise, the temperature of the

circulating water within the machine will soon

rise to a critical point, which will cause damage

to the sealing rings inside the machine.

• Don’t start and run the machine in a place

excessively cold so as to prevent the machine

from the freezing current.

• This machine has been designed for only using

cleaning water, do not use corrosive chemicals.

• Use cleaning agent supplied or recommend by

the manufacturer.

• High-pressure jets can be dangerous if subject

to misuse. The jet must not be directed at

persons, animals, live electrical equipment or

the machine itself. Pressure washers should

not be pointed at tire walls, as it may be

possible to damage them.

• Do not direct the jet against yourself or others

in order to clean clothes or footwear.

• Disconnect from the electrical power supply

before carrying out user maintenance.

• If the mains cable is damaged it must be

replaced by the manufacturer, or its service

agent or similarly qualified person to avoid a

hazard.

• Do not use the machine if a supply cord or

important parts are damaged, e.g. safety

devices, high pressure hoses, trigger gun.

• Be aware of the recoil caused by the water jet

when the machine is switched on.

• When the machine is moving and installing, the

machine must be in flat. When moving the

machine, pulling the handle to move it.

• Connect to the water supply. The machines are

not suitable for connection to portable water

mains. Connect the machine to the water

supply. (It can be a water container).

• Make sure the inlet water pressure keeps

between 0.01MPa and 0.4MPa.The inlet pipe

should at least 5 M long. Do not use the pipe if

the pipe is damaged. If you want connect this

machine to portable water mains, you must

install a backflow preventer in the water pipe to

prevent dirty water flow back to the drinking

water system. The backflow preventer shall

comply with EN 60335-2-79 ANNEX AA.

3. Assembly and use

The motor of this pressure washer will

NOT run. It will only operate when the

trigger is squeezed.

• Connect the outlet hose to the washer and

connect the spray gun to the outlet hose.

• Connect nozzle and nozzle extension.

• Check gauze filter is clear of any blockage.

• Connect the water supply hose.

• Check that the hose has no kinks in it.

• Turn on water and check for leaks.

• Depress trigger to allow air to be expelled

though the pump and hoses, lock trigger.

• Plug in machine and turn on switch.

• Unlock trigger and use the pressure washer.

Shut down

1. Turn off the motor(push switch to the off

position).

2. Unplug the unit from the power source.

3. Turn off the water supply.

4. Press the trigger of the gun to depressurize the

system.

5. Disconnect the garden hose from the pressure

washer.

6. Wipe all surfaces of the unit with a damp clean

cloth.

7. Engage the gun safety lock.

CAUTION: ALWAYS turn off the unit’s motor

BEFORE turning off the unit’s water supply.

Serious damage could occur to the motor if the

unit is run without water.

CAUTION: NEVER disconnect the high-pressure

discharge hose from the machine while the system

is still pressurized. To depressurize the unit, turn

off the motor, turn off the water supply and

squeeze the trigger 2-3 times

Water supply

• Ensure that you have a suitable water supply to

feed the pressure washer. Check that all

connections are tight and there are no leaks in

the hose.

• The supply tap should be fully open (do not

turn on the pressure washer yet).

• Now depress the trigger (unlock trigger lock

first) to let water pass through the unit and

expel any air.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm GRM1010 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info