Bedienungsanleitung Ferm GRM1011 (Seite 8 von 24) (Englisch)

763657

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

washer.

6. Wipe all surfaces of the unit with a damp clean

cloth.

7. Engage the gun safety lock.

CAUTION:ALWAYSturnofftheunit’smotor

BEFORE turning off the unit’s water supply.

Serious damage could occur to the motor if the

unit is run without water.

CAUTION:NEVERdisconnectthehigh-pressure

discharge hose from the machine while the system

is still pressurized. To depressurize the unit,

turn off the motor, turn off the water supply and

squeeze the trigger 2-3 times



• Ensurethatyouhaveasuitablewatersupply

to feed the pressure washer. Check that all

connections are tight and there are no leaks in

the hose.

• Thesupplytapshouldbefullyopen(donot

turn on the pressure washer yet).

• Nowdepressthetrigger(unlocktriggerlock

first) to let water pass through the unit and

expel any air.

Warning! This unit is to be used with a

cold-water source only!

• Turnonthepressurewasher,oncealltheair

has been expelled and water has reached the

end of the lance.



• Ensurethatallcablesaredamagefreebefore

connecting to the power supply.

Plug in the pressure washer and turn the unit

on with the main switch (2).



CAUTION! The cleaner must only be

used with clean water; use of unfiltered

water or corrosive chemicals will damage

the cleaner.

• Turnthemotorswitchtothe“0”position.

• Checkthattheelectricalsupplyvoltageand

frequency (Volts/Hz) correspond to those

specified on the cleaner data plate.

• Ifthepowersupplyiscorrect,youmaynow

plug in the cleaner.

• Theelectricsupplyconnectionshallbemade

by a qualified electrician. It is recommended

that the electric supply to this appliance should

include either a residual current device that

will interrupt the supply if the leakage current

to earth exceeds 30 mA for 30 ms or a device

which will prove the earth circuit.

CAUTION! The machine may cause

electrical disturbances when starting.

• Ifthemotorstopsandfailstorestart,wait2-3

minutes before restarting. THERMAL CUTOUT

TRIPPED



Fig. 2

• Watermaybesprayedoutofthenozzleeither

linearly or in a fan shape. Turn on the pressure

first, and then adjust the nozzle.



Fig. 3

• Thewaterinletfiltermustbeinspectedregu-

larly, so as to avoid blockage and restriction of

the water supply to the pump. (fig 3)



Fig. 4

• Thedetergentnozzleandtankattachesto

the end of the trigger assembly in the same

way as the lance does. Fill the detergent tank

with liquid detergent. When the trigger is now

pressed with the machine running, detergent

will spray out with the water.

• Recommendedcleaningprocedure

• Dissolvedirtbyapplyingdetergentwiththefan

jet to the dry surface.

• Onverticalsurfaces,workfromthebottom

upwards. Leave the detergent to act for 1 to 2

minutes, but do not allow to dry out. Apply the

high pressure jet, keeping the nozzle at least

30 cm (10 in.) from the surface, working from

the bottom upwards. Avoid allowing the rinsing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm GRM1011 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info