Bedienungsanleitung Ferm GRM1018 (Seite 8 von 16) (Englisch)

763695

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

washer.

6. Wipe all surfaces of the unit with a damp clean

cloth.

7. Engage the gun safety lock.

CAUTION: ALWAYS turn off the unit’s motor

BEFORE turning off the unit’s water supply.

Serious damage could occur to the motor if the

unit is run without water.

CAUTION: NEVER disconnect the high-pressure

discharge hose from the machine while the

system is still pressurized. To depressurize the

unit, turn off the motor, turn off the water supply

and squeeze the trigger 2-3 times

Water supply

• Ensure that you have a suitable water supply

to feed the pressure washer. Check that all

connections are tight and there are no leaks in

the hose.

• The supply tap should be fully open (do not

turn on the pressure washer yet).

• Now depress the trigger (unlock trigger lock

first) to let water pass through the unit and

expel any air.

Warning! This unit is to be used with a

cold-water source only!

• Turn on the pressure washer, once all the air

has been expelled and water has reached the

end of the lance.

Electrical Cables

• Ensure that all cables are damage free before

connecting to the power supply.

Plug in the pressure washer and turn the unit

on with the main switch (2).

4. USE

CAUTION! The cleaner must only be

used with clean water; use of unfiltered

water or corrosive chemicals will damage

the cleaner.

• Turn the motor switch to the “0” position.

• Check that the electrical supply voltage and

frequency (Volts/Hz) correspond to those

specified on the cleaner data plate.

• If the power supply is correct, you may now

plug in the cleaner.

• The electric supply connection shall be made

by a qualified electrician. It is recommended

that the electric supply to this appliance

should include either a residual current device

that will interrupt the supply if the leakage

current to earth exceeds 30 mA for 30 ms or a

device which will prove the earth circuit.

CAUTION! The machine may cause

electrical disturbances when starting.

• If the motor stops and fails to restart, wait 2-3

minutes before restarting. THERMAL CUTOUT

TRIPPED

Adjusting the nozzle

Fig. 2

• Water may be sprayed out of the nozzle either

linearly or in a fan shape. Turn on the pressure

first, and then adjust the nozzle.

Adjusting pressure

Fig. 3

Using High Pressure:

• Please make sure the trigger released and

there is not any water spraying. then turn the

rear part of spray nozzle counterclockwise.

Squeeze the trigger, the gun will spray water

with high pressure.

Using Low Pressure:

• Please make sure the trigger released and

there is not any water spraying. then turn the

rear part of spray nozzle clockwise. Squeeze

the trigger, the gun will spray water with low

pressure.

CAUTION: Selection of high or low

pressure by turning action. The selection

of the pressure must be carried out with

the gun in closed position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm GRM1018 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info