Bedienungsanleitung Ferm GRM1022 (Seite 7 von 20) (Englisch)

763660

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Warning! This unit is to be used with a

cold-water source only!

• Turn on the pressure washer, once all the air

has been expelled and water has reached the

end of the lance.

Electrical Cables

• Ensure that all cables are damage free before

connecting to the power supply.

Plug in the pressure washer and turn the unit

on with the main switch (2).

4. USE

CAUTION! The cleaner must only be

used with clean water; use of unfiltered

water or corrosive chemicals will damage

the cleaner.

• Turn the motor switch to the “0” position.

• Check that the electrical supply voltage and

frequency (Volts/Hz) correspond to those

specified on the cleaner data plate.

• If the power supply is correct, you may now

plug in the cleaner.

• The electric supply connection shall be made

by a qualified electrician. It is recommended

that the electric supply to this appliance

should include either a residual current device

that will interrupt the supply if the leakage

current to earth exceeds 30 mA for 30 ms or a

device which will prove the earth circuit.

CAUTION! The machine may cause

electrical disturbances when starting.

• If the motor stops and fails to restart, wait 2-3

minutes before restarting. THERMAL CUTOUT

TRIPPED

Adjusting the nozzle

Fig. 2

• Water may be sprayed out of the nozzle either

linearly or in a fan shape. Turn on the pressure

first, and then adjust the nozzle.

Water inlet filter

• The water inlet filter must be inspected regu-

larly, so as to avoid blockage and restriction of

the water supply to the pump.

CAUTION! Never disconnect the high-

pressure hose from the machine while

the system is still pressurized.

5. SERVICE & MAINTENANCE

Warning! Unplug the electric cable

(power source) prior to any maintenance

or preparatory storage operations.

• Make sure that the machine is not live when

carrying out maintenance work on the motor.

• To ensure good performance, check and clean

the suction and detergent filters after every 50

hours of operation.

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

1. When switched on, the machine will not

start working.

• Plug is not well connected or electric socket is

faulty.

• Check plug, socket and fuse.

• The mains voltage is lower than the minimum

requirement for start up.

• Check that the mains voltage is adequate.

• The pump is stuck.

• Refer to after storage instructions. Switch

off the unit and let the motor cool.

• Thermal safety has tripped.

• Leave the lance open with water coming

through.

2. Fluctuating pressure

• Pump sucking air

• Check that hoses and connections are

airtight

• Valves dirty, worn out or stuck. Pump seals worn.

• Clean and replace or refer to dealer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm GRM1022 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm GRM1022

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info