Bedienungsanleitung Ferm GRM1026 (Seite 8 von 40) (Englisch, Französisch, Türkisch)

763929

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

• Wipe all surfaces of the unit with a damp clean

cloth.

• Engage the gun safety lock. (Fig. 7)

CAUTION: ALWAYS turn off the unit’s

motor BEFORE turning off the unit’s

water supply. Serious damage could

occur to the motor if the unit is run

without water.

CAUTION: NEVER disconnect the high-

pressure discharge hose from the

machine while the system is still

pressurized. To depressurize the unit,

turn off the motor, turn off the water

supply and squeeze the trigger 2-3 times

Warning! This unit is to be used with a

cold-water source only!

Electrical Cables

• Ensure that all cables are damage free before

connecting to the power supply.

Plug in the pressure washer and turn the unit

on with the main switch (2).

4. USE

CAUTION! The machine may cause

electrical disturbances when starting.

• If the motor stops and fails to restart, wait 2-3

minutes before restarting. THERMAL CUTOUT

TRIPPED

Adjusting the nozzle

Fig. 2

• Water may be sprayed out of the nozzle either

linearly or in a fan shape. Turn on the pressure

first, and then adjust the nozzle.

Adjusting the working pressure

Fig. 3

The working pressure can be adjusted by sliding the

end of the adjustable spray gun back or forward.

• Slide backward to increase the working

pressure.

• Slide forward to reduce the working pressure.

Using detergents

Fig. 1 & 3

The built-in detergent dispenser will allow you

to apply many forms of liquid detergent onto the

work surface. Detergent application happens at

low-pressure only.

• Insert the adjustable nozzle onto the gun.

•

Adjust the nozzle to low pressure setting. (Fig. 3)

• Remove the cap on the detergent reservoir

(11 in Fig. 1) and fill with liquid detergent only.

Do not put any water into the reservoir. The

pressure washer will mix water and detergent

automatically. When finished applying the

detergent to the work surface, it is possible

to spray off the detergent by using the high-

pressure setting (Fig. 3). In high-pressure mode,

the pressure washer will not dispense detergent.

Adjusting the detergent rate

Fig. 4

To adjust the rate detergent is mixed with the

water you can turn the detergent knob.

• Turn left to decrease the amount of detergent

added.

• Turn Right to increase the amount of detergent

added.

Water inlet filter

• The water inlet filter must be inspected regu-

larly, so as to avoid blockage and restriction of

the water supply to the pump.

CAUTION! Never disconnect the high-

pressure hose from the machine while

the system is still pressurized.

5. SERVICE & MAINTENANCE

Warning! Unplug the electric cable

(power source) prior to any maintenance

or preparatory storage operations.

• Make sure that the machine is not live when

carrying out maintenance work on the motor.

• To ensure good performance, check and clean

the suction and detergent filters after every 50

hours of operation.

• When the nozzle is clogged, it may cause

failure. The nozzle can be cleaned by inserting

the ‘cleaning pin’ into the tip to remove filth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm GRM1026 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info