Bedienungsanleitung Ferm HDM1020 (Seite 5 von 60) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

763645

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Special safety instructions

• Wear a hard safety helmet, safety glasses and/

or face shield. It is also highly recommended

that you wear a dust mask, ear protectors and

thickly padded gloves.

• Be sure the bit is secured in place before

operation.

• Under normal operation, the tool is designed

to produce vibration. Check tightness of

screws carefully before operation to avoid a

breakdown or accident.

• In cold weather or when the tool has not been

used for a long time, let the tool warm up for

several minutes by operating it under no load.

This will loosen up the lubrication. Without

proper warm-up hammering operation is

difficult.

• Always be sure you have firm footing. Be sure

no one is below when using the tool in high

locations.

• Hold the tool firmly with both hands.

• Keep hands away from moving parts.

• Do not point the tool at any one in the area

when operating. The bit could fly out and injure

someone seriously.

• Do not touch the bit or parts close to the bit

immediately after operation; they may be

extremely hot and could burn your skin.

• Always use the auxiliary grip to reduce the risk

of loss of control. Risk of personal injury.

• Hold the machine by the insulated gripping

surfaces where the accessory may contact

hidden wiring or the mains cable. If the

accessory contacts a ‘live’ wire, the exposed

metal parts of the machine can also become

‘live’. Risk of electric shock.

• After use, do not touch the tip of the

accessory.

When chipping into walls, floors or

wherever “live” electrical wire may be

encountered, do not touch any metal

parts of the tool!

Electrical safety

Always check that the mains voltage is

the same as on the type plate of the

machine.

Replacement of power cords or plugs

Immediately dispose of old cords and plugs once

they have been replaced. It is dangerous to plug a

loose power cord into a mains power socket.

Use of extension leads

Only ever use approved extension leads that are

suitable for the power rating of the machine. The

minimum core thickness is 1.5 mm2. Whenever

using a reel extension lead, always fully unroll the

lead.

3. ASSEMBLY

Mounting tool bits

Fig. 3

Before exchanging a bit, first remove the

power plug from the mains.

• Lightly oil the bit shaft before inserting it into

the tool holder.

• Rotate the stop lever 180º clockwise, while

pulling it towards you

• Insert the tool shank into the hexagonal tool

holder: the flat side of the bit towards the side

of the stop lever.

• Rotate the stop lever 180º counterclockwise to

lock the bit.

Auxiliary handle

Fig. 2

The auxiliary handle can be adjusted to several

positions to have a good control to the tool.

4. OPERATION

Before operation: Ensure the power

switch is in OFF position. If the plug is

connected to the mains while the switch

is in ON position the machine will start

immediately, which could cause serious

injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm HDM1020 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info