Bedienungsanleitung Ferm HDM1021 (Seite 6 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510087

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

6 Ferm

the chuck (4).

• Turn the auxiliary grip (7) to the required

position.

• Tighten the auxiliary grip (7) by turning it

clockwise.

Removing

• Loosen the auxiliary grip (7) by turning it

counterclockwise.

• Remove the auxiliary grip (7).

• Tighten the auxiliary grip (7) by turning it

clockwise.

Mounting and removing the depth stop

(fig. C)

Mounting

• Loosen the auxiliary grip (7) by turning it

counterclockwise.

• Insert the depth stop (8) through the hole in

the auxiliary grip (7).

• Set the depth stop (8) to the required position.

• Tighten the auxiliary grip (7) by turning it

clockwise.

Removing

• Loosen the auxiliary grip (7) by turning it

counterclockwise.

• Remove the depth stop (8).

• Tighten the auxiliary grip (7) by turning it

clockwise.

Mounting and removing the dust collector

(fig. D)

The dust collector prevents dust from entering the

machine when drilling into ceilings.

Immediately replace a damaged dust

collector.

Mounting

• If necessary, remove the accessory from the

chuck (4).

• Slide the dust collector (15) over the shaft of

the accessory.

• Insert the accessory with the dust collector

(15) into the chuck (4).

Removing

• Remove the accessory with the dust collector

(15) from the chuck (4).

• Remove the dust collector (15) from the

accessory.

Use

Switching on and off

(fig. A)

• To switch on the machine, press the on/off

switch (1).

• To switch off the machine, release the on/off

switch (1).

Setting the operating mode

(fig. A & E)

The drill selection switch and the hammer

selection lever must be set according to the

required operating mode. Refer to the table below

to set the required operating mode.

Setting (fig. E) Operating mode

A Demolition hammer / Chisel

B Hammer drill

C Drill

• Turn the drill selection switch (2) and the

hammer selection lever (3) to the required

position.

Speed Preselection

The required speed can be preselected with the

thumbwheel. Also during running the rotational

speed can be adjusted.

1 – 2 = low speed

3 – 4 = medium speed

5 – 6 = high speed

Max = maximum speed

The required speeds depends on the material and

can be determined by practical testing.

Hints for optimum use

• Clamp the workpiece. Use a clamping device

for small workpieces.

• Firmly hold the machine by the grip.

• Set the operating mode.

• Switch on the machine.

• Do not apply too much pressure on the

machine. Let the machine do the work.

• Switch off the machine and wait for the

machine to come to a complete standstill

before putting the machine down.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm HDM1021 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info