Bedienungsanleitung Ferm HDM1048 (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

763894

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

4. OPERATION

Hammer drills require very little operator

pressure. Excessive pressure on the tool

can lead to unnecessary overheating of

the motor, and burning of the driven tool.

It also may happen the drill bit deforms

and cannot be removed from the machine

again.

The On/Off switch (fig. A)

• Switch the machine on by pressing the On/Off

switch (1). When releasing the On/Off switch

(1) the machine will turn off.

• The rotation-speed can be continuously

adjusted by pressing the On/Off switch (1)

deeper or less deep.

Switching the direction of rotation (fig. A)

• Direction of rotation counter-clockwise: shift

left/right switch (2) to “ ”.

• Direction of rotation clockwise: shift left/right

switch (2) to “ ”.

Function selection switch (fig. A)

In order to avoid damage to the machine,

adjusting the function selection switch

(5) shall only be done when machine is

not running

• Set the function selection switch (5) to “ ” for

drilling.

• Set the function selection switch (5) to “ ” for

hammer drilling.

User tips

• For large holes, for instance in very hard

concrete, start using a smaller bit for pilot

drilling first, then drill to nominal size.

• Hold the machine firmly with 2 hands. Be

aware the drill can jam and because of that

machine might suddenly turn (especially when

drilling deep holes).

• Do not apply a lot of pressure on the machine,

let the machine do the work.

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

battery pack from the machine.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that

the ventilation openings are free of dust and

dirt. Remove very persistent dirt using a soft

cloth moistened with soapsuds. Do not use any

solvents such as gasoline, alcohol, ammonia,

etc. Chemicals such as these will damage the

synthetic components.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be

collected at the appropriate recycling

locations.

Only for EC countries

Do not dispose of power tools into domestic

waste. According to the European Guideline

2012/19/EC for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

WARRANTY

FERM products are developed to the highest

quality standards and are guaranteed free of

defects in both materials and workmanship for the

period lawfully stipulated starting from the date

of original purchase. Should the product develop

any failure during this period due to defective

material and/or workmanship then contact your

FERM dealer directly.

The following circumstances are excluded from

this guarantee:

• Repairs and or alterations have been made

or attempted to the machine by unauthorized

service centers.

• Normal wear and tear.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm HDM1048 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info