Bedienungsanleitung Ferm JBM1001 (Seite 3 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510133

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Ferm

HYDRAULIC JACK

The numbers in the following text refer to the

picture on page 2

For your own safety and that of others, we

recommend that you read this instruction

manual carefully before using this

machine. Keep this instruction manual

and the documentation provided with the

saw for future reference.

Know your apparatus

Before attempting to operate the apparatus,

familiarise yourself with the controls and make

sure you know how to stop it quickly in an

emergency.

Contents

1. Safety instructions

2. Using the apparatus

3. Service & maintenance

Technical specifications

Fig. 1

Lpa Sound pressure level <70dB(A)

1. Safety instructions

Explanation of the symbols

Denotes risk of personal injury, loss of life

or damage to the tool in case of non-

observance of the instructions in this

manual.

Special safety rules

Non-observance of the following instructions can

cause personal injuries and/or damage to the

vehicle.

• Beforejackingupthecar,makesurethejack

is as near to the wheel to be lifted as possible

and as far under the body or any other point of

support as possible.

• Themaximumloadindicatedonthejackmust

neverbeexceeded.

• Thejackmustbeusedasaliftingdeviceonly.

• Alwaysplacethejackonahardandlevel

surface.

• Alwaysprotectthecarfromrollingaway.

Before jack ing up the car, place chocks behind

and in front of the wheels remaining on the

ground, if necessary. Put the car in first gear or

put on the handbrake to further block the car.

• Makesuretoplacethejackinsuchawaythat

your hand is not underneath the car when

jacking it up.

• Makesurethejackisplacedvertical.

• Foryourownsafety,beforeworkingor

crawling underneath the car jack up the car

and support the shafts.

• Beforeusingtheshaftsupportsmakesure

they are in good condition.

• Shouldthepressureinthejackbecometoo

high,excessairwillescapethroughtherelief

valve.Thereliefvalvehasbeensetinthe

factory.

2. Using the apparatus

Assembling the jacking beam

Telescopebothpartsofthejackingbeam,allowing

the flat side to be used when opening and closing

the cock to lower the jack.

Lifting

• Putthecarin‘1’orengagethehandbrake

and block the wheels to prevent the car from

moving.

• Closethecockbymeansofthejackingbeam.

• Instalthescrewjackintherightplace

(indicated by the car manufacturer).

• Insertthejackingbeamintothejackingpoint

and move the jacking beam up and down.

Shaft supports

• Afterjackingupthecartheshaftsupports

should be installed.

• Lowerthecarbyturningthethescrewofthe

release valve anticlockwise, until the car rests

on the supports. Never work under a car which

only rests on the trolley jack.

Lowering

Fig. 1

When you have finished the job, jack up the car

until the jack stands are free. Remove the jack

stands. Using the jacking beam, very slowly and

counterclockwise open the cock referred to under

3. Service & maintenance

Regular maintenance of the hydraulic

jack prevents unnecessary problems.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm JBM1001 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info