Bedienungsanleitung Ferm JSM1033 (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

763897

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Replacing the saw blade

Fig. A, B

When mounting the saw blade, wear

protective gloves. Danger of injury when

touching the saw blade.

Only use saw blades that correspond

with the characteristic data given in the

operating instructions.

Fold the Guard (12) upwards before replacing

the saw blade. Always saw with the guard folded

downwards.

Mounting the saw blade

Make sure the blade holder is free of material

debris (such as splinters of wood or metal).

1. Turn the clamping lever (13) as far to the left as

possible and hold it in this position.

2. Insert the saw blade in the chuck (16). Check

that the saw blade is securely fixed and that

the teeth are pointing in the cutting direction.

3. Let go of the clamping lever. Check whether

the back of the saw blade is positioned in the

centre of the guide roller (10). Make sure to

use the right sawblade for the corresponding

material. Included with the machine is a coarse

sawblade for wood and a fine sawblade for

metal and plastics.

Removing the saw blade

1. Turn the clamping lever (13) as far to the left as

possible and hold it in this position.

2. Remove the saw blade from the chuck (16).

3. Let go of the clamping lever.

Attaching the parallel guide

Fig. C

1. Loosen the bolts (14).

2. Mount the parallel guide (19) onto the

baseplate (9).

3. Set the desired cutting width using the scale

on the parallel guide (19) and the cutting mark

on the baseplate (9). The cutting mark (21)

indicates the position of the saw blade.

4. Tighten the bolts (14).

4. OPERATION

Switching the machine on/off

Fig. A

The on/off switch (2) is used for activating the

machine and adjusting speed.

•

To start the machine, press and hold the lockoff

button (1) and press the on/off switch (2).

• The further the on/off switch (2) is being

pushed, the faster the blade will move. The

required speeds depends on the material and

can be determined by practical testing.

• To stop the machine, release the on/off switch

(2).

Adjusting the bevel angle

Fig. A, D

1. Loosen the bolts (18), using the hex key (15).

2. Adjust the baseplate (9) to the desired position

(0°- 45°). The sawing angle (bevel) can be read

on the scale (7).

3. Tighten the bolts (18), using the hex key (15).

It is possible to store the hex key onto the

machine, as shown on Fig. A.

Adjusting the pendulum action

Fig. A

The pendulum action switch (6) is used to set the

way in which the teeth of the saw blade grip the

material. The pendulum action switch can be set

to 4 positions:

0 - No pendulum action

1 - Small pendulum action

2 - Medium pendulum action

3 - Large pendulum action

The required pendulum action can be determined

by practical testing, although the following

instructions can be observed:

• Soft material (wood, plastics etc.): set the

pendulum to level II or III. For a finer and

cleaner saw cut, use pendulum level 0 or I.

• Thin material, use pendulum level 0.

• Hard material (hardwood, steel etc.): set the

pendulum to level 0.

• Curves: set pendulum to level 0.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm JSM1033 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info