Bedienungsanleitung Ferm JSM1034 (Seite 8 von 44) (Englisch, Holländisch)

763898

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

4. OPERATION

Switching on and off

Fig. A

• To switch the machine on, push the switch

forward and press the On/off switch (1).

• To switch the machine off, release the On/off

switch (1).

Setting the speed

Fig. A

The speed adjustment wheel (5) is used for setting

the speed. The ideal speed depends on the profile

and the teeth of the saw blade and on the material

to be worked.

Do not set the speed during use.

• Turn the speed adjustment wheel (5) to the

required position.

- For hard materials, use a saw blade with fine

teeth and select a lower speed.

- For soft materials, use a saw blade with coarse

teeth and select a higher speed.

Adjusting the bevel angle

Fig. A, D

1. Loosen the bolts (16), using the hex key (13).

2. Adjust the baseplate (9) to the desired position

(0°- 45°). The sawing angle (bevel) can be read

on the scale (7).

3. Tighten the bolts (16), using the hex key (13).

It is possible to store the hex key onto the

machine, as shown on Fig. A.

Adjusting the pendulum action

Fig. A

The pendulum action switch (6) is used to set the

way in which the teeth of the saw blade grip the

material. The pendulum action switch can be set

to 4 positions:

0 - No pendulum action

1 - Small pendulum action

2 - Medium pendulum action

3 - Large pendulum action

The required pendulum action can be determined

by practical testing, although the following

instructions can be observed:

• Soft material (wood, plastics etc.): set the

pendulum to level II or III. For a finer and

cleaner saw cut, use pendulum level 0 or I.

• Thin material, use pendulum level 0.

• Hard material (hardwood, steel etc.): set the

pendulum to level 0.

• Curves: set pendulum to level 0.

Dust extraction

Fig. E

• Connect the hose of a vacuum cleaner to the

dust extraction adapter (8).

Note: the dust blow function must be de-

activated when using a vacuum cleaner.

Dust blow function

Fig. G

The cutting line can be kept clear of chips and

debris by using the dust blow function.

• To activate the dust blow function, move the

dust blower switch (2) to the right, as shown

on figure G1.

• To de-activate the dust blow function, move

the dust blower switch (2) to the left, as shown

on figure G2.

Optimum use

• Clamp the workpiece. Use a clamping device

for small workpieces.

• Draw a line to define the direction in which to

guide the saw blade.

• Firmly hold the machine by the grip.

• Set the sawing speed.

• Set the mitre angle.

• Switch on the machine.

• Wait until the machine has reached full speed.

• Place the saw shoe on the workpiece.

• Slowly move the machine along the pre-drawn

line, firmly pressing the saw shoe against the

workpiece.

• Do not apply too much pressure on the

machine. Let the machine do the work.

• Switch off the machine and wait for the

machine to come to a complete standstill

before putting the machine down.

5. MAINTENANCE

Before cleaning and maintenance,

always switch off the machine and

remove the mains plug from the mains.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm JSM1034 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info