Para regular a velocidade da corrente de ar, o soprador deve ser manuseado a qualquer velocidade entre lenta e aceleração máxima.
Aconselhamos que cada utilizador teste as diferentes posições do acelerador para encontrar a que mais lhe convém.
Funcionamento do aspirador
Fig. 7
ATENÇÃO! NUNCAUTILIZE O ASPIRADOR SEM QUE O SACO TENHASIDO DEVIDAMENTE COLOCADO E FECHADO.
Nunca aspire objectos quentes ou a arder (ex: cinzas ou cigarros) de lareiras ou churrascos.
Aguarde sempre que estes objectos arrefeçam e apaguem por completo.
Nunca utilize o aparelho perto duma fogueira ou qualquer tipo de chama a arder.
ATENÇÃO! Este aparelho foi concebido para aspirar pequenos resíduos como folhas, pequenos pedaços de papel, rebentos,
relva, etc.
Não tente aspirar pedras, vidro partido, garrafas, latas de alumínio ou quaisquer outros objectos. Pode resultar na avaria do aparelho, bem
como no ferimento do próprio utilizador.
Se o tubo do aspirador estiver a ser utilizado na horizontal, pode sugar pedras e outros objectos que possam danificar o aparelho.
Trabalhar com o aspirador:
• Siga as instruções de arranque já mencionadas neste manual.
• Permita que o aparelho alcance uma velocidade lenta e constante. Apoie a alça no ombro direito fazendo passar o aparelho por baixo do
braço esquerdo.
ATENÇÃO! Tenha cuidado para que, durante o funcionamento, a alça não bloqueie a saída do ar. O silenciador produz calor, o
que poderia queimar, derreter e danificar a alça.
• Coloque a mão esquerda no topo do punho principal e com a mão direita segure no punho lateral
• Balance o aparelho de um lado para outro ao aspirar.
ATENÇÃO! Para evitar entupir o tubo, não o force, nem o introduza numa pilha de resíduos.
Tubo entupido
Desentupir o tubo:
• Desligue o aparelho. Comprima o saco colector enquanto tem volume, expelindo o ar pelo tubo. Esta saída do ar geralmente é suficiente
para desobstruir o tubo. Se tal não acontecer, proceda da seguinte maneira:
• Remova e inspeccione os tubos.
• Limpe cuidadosamente o bocal.
• Volte a instalar os tubos.
Ferm 45
GB
D
NL
F
E
P
• Use the full blower nozzle extension so the air stream can work close to the ground.
• Watch out for children, pets, open windows etc. and blow debris safety away.
What not to do
WARNING! DO NOT USE ANY OTHER FUEL than that recommended in your manual. Always follow instructions in the Fuel and
Lubrication Section of this manual. Never use petrol unless it is correctly mixed with 2- cycle engine lubricant. Permanent
damage to the engine will result, invalidating the manufacturer’s warranty.
• DO NOT SMOKE while refuelling or operating the equipment.
• DO NOT OPERATE THE UNIT WITHOUTAMUFFLER and correctly installed muffler shield.
• DO NOTTOUCH or let your hands or body come in contact with a hot muffler or spark plug wire.
• DUE TO THE DANGER of exhaust fumes, never operate the blower in a confined or poorly ventilated area.
• NEVER POINTTHE BLOWER in the direction of people, animals, buildings, automobiles, or windows, etc.
• DO NOT operate the unit without the inlet cover installed to prevent contact with the impeller.
• DO NOT set a hot engine down where inflammable material is present.
• DO NOT OPERATE THE UNIT FOR PROLONGED PERIODS. Rest periodically.
WARNING! DO NOT ADD, REMOVE OR ALTER ANYCOMPONENTS OF THIS PRODUCT. Doing so can cause personal injury
and/or damage the unit voiding the manufacturer’s warranty.
• DO NOT OPERATE THE UNIT WHILE UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.
• DO NOT operate your unit near or around flammable liquids or gases whether inside or outdoors. An explosion and/or fire can result.
• DO NOT WEAR loose clothing, scarves, neck chains, unconfined long hair, and the like. Doing so can cause injury associated with
objects being drawn into the rotating parts.
• DO NOT refuel a running engine or an engine that is hot.
• Never allow children to operate the appliance.
3. ASSEMBLYINSTRUCTIONS
Blower attachment assembly instructions
Fig. 2A+ 2B
• Loosen the screws (A) and remove the screw (B). Insert the blower tube (C) into the blower housing and replace screw (B). Tighten
screws (A).
• Insert speed cleaner head (D) to the tube (C).
Harness installation
Fig. 3
Attach the 2 harness clips to the 2 links in the blower handle.
Vacuum attachment assembly instructions
Fig. 4
• Pull the slide (A) forward & fit bag (B) into the vacuum housing.
• Insert speed cleaner head (D) to the tube (C).
Fuel and lubrication
Fuel
Use regular grade unleaded petrol mixed with 40:1 custom 2-cycle engine oil for best results. Use mixing ratios in the FUELMIXING TABLE.
WARNING! Never use straight petrol in your unit. This will cause permanent engine damage and invalidate the manufacturer’s
warranty for that product. Never use a fuel mixture that has been stored for over 90 days.
WARNING! If 2-cycle lubricant other than custom lubricant is to be used, it must be a premium grade oil for 2-cycle air cooled
engines mixed at a 40:1 ratio. Do not use any 2-cycle oil product with a recommended mixing ratio of 100:1. If insufficient
lubrication is the cause of engine damage, it will invalidate the manufacturer’s engine warranty.
Mixing fuel
Add the oil to an approved fuel container followed by the gasoline to allow incoming gasoline to mix with oil. Shake the container to ensure
thorough mix.
WARNING! Lack of lubrication will invalidate the engine warranty. Petrol and oil must be mixed at 40:1.
08 Ferm
GB
D
NL
F
E
P
