Bedienungsanleitung Ferm li ion fdsc 360 lk (Seite 5 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Norwegisch)

381265

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Product information

Fig. 1

1. Bit holder

2. On/Off-switch

3. Softgrip

4. LED (Red)

5. Charger connection

6. Extension piece

7. Bit

8. LED (White)

2. SAFETY INSTRUCTIONS

Explanation of the symbols

DESCRIPTION (FIG. A)

Denotes risk of personal injury, loss of

life or damage to the tool in case of

non-observance of the instructions in

this manual.

Indicates electrical shock hazard.

Indoor use only

In case of failure, the transformer is not

dangerous

Thermic protector

Do not dispose of in household waste.

Specific safety instructions

• Only use the accumulator block with the

battery charger provided – using other

chargers could be dangerous.

• Keep the accumulator block, tool and battery

charger away from damp and wet conditions.

• Before using the battery charger, check all

wires are properly connected.

• If any wires on the charger are damaged, do

not use it until these have been replaced.

• When the charger is not in use it should not be

plugged in.

When unplugging, do not pull the plug out by

the cable.

• If the charger breaks down or suffers from

other technical problems, take it to a

recognised dealership to be checked before

using it again. Any damaged parts must be

replaced.

• Take care when handling the accumulator

block, do not drop it or knock it against other

things.

• Never attempt to repair the battery charger or

accumulator block yourself; this can be

extremely dan gerous. Repairs should always

be carried out by a recognised dealership.

• Always unplug the charger before cleaning or

carrying out any other maintenance on it.

• Do not attempt to charge the accumulator

block in temperatures of below 5 degrees or

above 40 degrees centigrade.

• Never throw the accumulator block into water

or a re – it may explode.

• Turn the drill immediately off after the screw is

fasten ed. Overloading and damaging the

battery or motor can be prevented this way.

Use the torque to loosen the fastened screw

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of re, electric shock and personal

injury.

Read the following safety instructions and also

the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class ll machine. Your machine is

double insulated; therefore no earthwire

is required.

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

3. ASSEMBLING INSTRUCTIONS

Inserting and removing bits

Fig. 1 + 7

The bits can easily be placed directly into the bit

holder or on the extension piece. The extension

piece can be used for screws that are difcult to

reach.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm li ion fdsc 360 lk Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info