46 Ferm
AVAILABLE SPARE PARTS FOR FKZ-250 CUTTING-OFF MACHINE
REF. NR. DESCRIPTION FERM. NR.
002/003/004/005 LOCATION PLATE COMPLETE 402515
030 INLAY 402506
047 SOCKET HEAD BOLT M8X35 402517
048 FLANGE 402495
049 MOVABLE GUARD 402502
050 EXTENSION SPRING 402516
055 KNOB 402535
068 HANDLE HOUSING 402534
069 SWITCH 402501
070 CARBON TIPPED SAWBLADE 310360
-ROTOR 402497
- STATOR 402496
- CARBON BRUSH SET 402498
- CARBON BRUSH HOLDER 402533
- GEAR 402518
-DRIVE SHAFT 402519
- CAM WRENCH 402503
-SOCKET SPANNER 402504
Ferm 3
minium. Other materials can be flung away, get
caught in the saw blade or cause other dangers.
- The arrow on the saw blade, which indicates the
direction of rotation, must point in the same
direction as the arrow placed on the machine.
The saw blade teeth must point downwards on
the front of the saw.
- Check whether the saw blade is sharp, undama-
ged and well aligned. Press the saw head down-
wards after removing the plug.
Turn the saw blade by hand and see whether it
turns freely. Put the machine in the 45° position
and repeat the test. If the saw blade touches any-
where, it must be adjusted again.
- Keep the saw blade and the tensioning surfaces of
the clamps clean.
- The saw blade flange must always be mounted
with the tightened recess towards the saw blade.
- The flange screw must be tightened with a 13 mm
open-end wrench.
- Check whether all the tensioning devices and
interlocks are secure and that no single part
shows too great a clearance.
-Never use just your hands for sawing.
-Always secure the workpiece against the check,
so that it cannot topple or turn during sawing. No
impurities may be allowed to gather under the
workpiece.
-Make sure that the workpiece cannot move after
being sawn through, for example, because it is not
supported by the full surface.
- For sawing workpieces which are not being sup-
ported by the full surface, use fillings or another
machine.
- Replace table insert when worn.
- Use only saw blades recommended by the manufac-
turer and which conform to EN-847-1.
- Connect the machine to a dustcollecting device
when sawing.
- Check whether the sawn off pieces can be removed
laterally from the saw blade. Otherwise they can be
caught by the saw blade and flung away.
- Never saw several workpieces at the same time.
- Be especially careful when sawing large, very small
or awkwardly shaped workpieces.
- Be careful when double mitring.
- Use additional supports (tables, trestle or other)
for long workpieces, which will otherwise topple
from the machine table if they are not held.
- Do not use the machine to saw workpieces which
are so small that they can no longer be held safely.
-When sawing profile sections, work must be car-
ried out so that the workpiece cannot slide away
and the saw blade cannot become jammed. A pro-
filed workpiece must lie flat or be held by an auxi-
liary tool, as a result of which toppling or sliding
during work is prevented.
- Round workpieces such as pipes must be secured,
otherwise they will turn and there is a danger that
the saw blade will become jammed. Always secu-
re the workpiece against the check and on the
table, using a suitable auxiliary tool.
- There may be no nails or foreign objects in the
workpiece to be treated.
-In order to prevent damage to the ears, ear mufflers
must be used.
-In order to prevent accidents in case the machine is
switched on by mistake, the mains plug must be
removed from the power point before adjustments
are made to the check or saw head. The same
applies to changing the saw blad or accessories and
during maintenance of the machine.
-In order to prevent electric shocks, when connec-
ting the plug to the power point, the metal pins may
not be touched in any way whatsoever.
- Do not use the cable to remove the plug from the
power point. Protect the cable from oil, heat and
sharp edges.
- Never apply a detergent or lubricant to a saw bla-
de which is still rotating.
-In order to prevent fire, the machine may never
be used near inflammable liquids, vapours or
gases.
- Prevent injuries which can occur by not using the
original accessories. Only use the recommended
saw blades.
- Choose a saw blade in relation to the material to
be sawn.
WHEN THE MACHINE IS IN OPERATION
Do not allow routine, which occurs when
using the machine frequently, to lead to
mistakes. Remember that a slight lack of con-
centration can result in serious injuries in a
split second.
1. Do not use the cutting-off machine without guards
in position.
2. Before the first saw cut is made, allow the machine
to rotate for a while. Should unusual noises or
strong vibrations be observed, then switch off the
machine and remove the plug from the power point
in order to then determine the cause. Do not switch
the machine on before the cause has been establis-
hed and the fault has been remedied.
3. Make sure that the sawn off workpiece does not
become jammed, do not hold it, do not clamp it and
do not secure it against the check. It must be allowed
to move freely along the side of the saw blade. If the-
se conditions cannot be met, the sawn off workpiece
can be caught by the saw blade and flung away.
4. Avoid placing your hands in an unfavourable place,
whereby one or both hands may come into contact
with the saw blade as a result of a sudden displace-
ment.
5. Before you begin sawing, allow the saw blade to
reach its full revolutions.
