Bedienungsanleitung Ferm MSM1030 - FKZ-210 (Seite 9 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

634078

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Ferm

Turn the knob (10) anticlockwise and then set •

the angle desired (you can read this off on the

back of the machine. Then tighten the knob

(10) again by turning it clockwise.

Changing the carbon brushes

Fig. A

Make sure that the plug is not in the socket!•

Unscrew the covers (16) with a flat bladed •

screwdriver. Remove the carbon brushes with

the same type of brushes. Screw the covers

(16) tight again.

Note: Always replace both carbon brushes at the

same time. Never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. F

Press in the clamp of the dust bag (27) and slide

it onto the opening on the back of the machine.

The dust bag stays in place when you release the

clamp.

4. OPERATION

Using the mitre saw

Fig. 1

Before use, always check for faults or

defects!

Set the desired sawing angle of the machine.•

Put the plug into the socket.•

Fix the piece of work in place using the •

clamps (24): make sure that the material is

well clamped in place!

Hold the material tightly on the left side while •

making sure that you keep a safe distance

from the blade of the saw.

Turn on the machine using the switch (1).•

Make sure that the saw blade has reached full •

speed before allowing it to touch the piece of

work to be sawn.

Use knob (2) to raise the protective cover •

lock.

Now bring the saw slowly downwards so that •

the saw blade saws through the piece of work

and passes through the slot in the table. Do

not put any pressure on the saw. Give the

machine time to saw through the piece of

work.

Bring the machine gently up again and switch •

it off by letting go of the switch (1).

5. SERVICE & MAINTENANCE

Always make sure that the machine is

not connected to the mains electricity

when you carry out any maintenance of

the mechanism.

This machine has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

Repairs and servicing should only be

carried out by a qualified technician or

service firm.

Problem solving

1. The motor does not start

The plug is not in the socket•

The power cord is broken•

The switch is defective. Take the machine to •

your Ferm dealer for repair.

2. The saw cut is not even (jagged)

The saw blade must be sharpened•

The saw blade is mounted back to front•

The saw blade is clogged with resin or sawdust•

The saw blade is not suitable for the piece of •

work being used

3. The height and/or mitre lever is obstructed

Chips and/or dust must be removed•

4. The motor has difficulty in reaching full

speed

The extension cord is too thin and/or too long•

The mains voltage is less than 230 V•

5. The machine vibrates excessively

The saw blade is damaged•

6. The machine becomes excessively hot

The ventilation slots are blocked. Clean them •

out with a dry cloth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1030 - FKZ-210 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info