Bedienungsanleitung Ferm MSM1031 (Seite 5 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

493544

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

19. Flange

20. Screw

21. Extension pieces (left and right)

22. Lock-button saw blade

23. Bolts

24. On/off switch for laser

Package contents

1 Radial mitre saw

1 Dust bag

1 Clamp

1 Key for changing the saw blade

3 Support bar

1 Instructions for use

1 Safety instructions

1 Warranty card

Check the machine, loose parts and accessories

for any transport damage.



When using the machine, always

carefully follow the safety precautions

supplied and the safety instructions given

below.



Danger of bodily injury or material

damage.

Indicates electrical shock hazard.

Class ll machine. Your machine is double

insulated; therefore no earthwire is

required.

Keep bystanders at a distance

Wear eye and ear protectors

Before each use of the saw

Check the machine. If any part of the machine is

missing, bent or in any other way unusable, or

when an electrical defect occurs, turn the machine

off and take the plug out of the socket. Replace all

missing, damaged or defective parts before using

the machine again.

To fix the saw blade in the slot and to prevent

the piece of work from moving, follow the



• Choose a suitable saw blade for the work.

Use the crosscut saw only for sawing wood

and wood derivatives or light metal such as

aluminium. Other materials can jump away or

get caught in the saw blade or give rise to

other dangers.

• The arrow marked on the saw blade, which

indicates the direction of rotation, must point

in the same direction as the arrow marked on

the machine. The saw blade teeth must point

downwards on the front of the saw.

• Check that the saw blade is sharp,

undamaged and correctly aligned. After

unplugging the machine, push the saw hood

downwards. Rotate the saw blade by hand

and check that it revolves freely. Put the

machine in the 45° position and check free

rotation again. If the blade touches anything it

must be adjusted.

• Keep the saw blade and the clamping surface

for the clamps clean.

• The saw blade flange must always be

mounted with the notch tightened towards the

saw blade.

• Check that all tensioning devices and locks

are secure and that no part has too much play

in it.

• Never just use your hands for sawing.

• Always press the piece of work firmly against

the stop, so that it cannot tilt or turn while

sawing. No impurities must gather underneath

the piece of work being sawn.

• Make sure that the piece of work cannot move

after being sawn, for example because it is

not completely supported by the surface of

the machine.

• For sawing pieces of work that are not

supported by the full surface, use some

padding or another machine.

• Replace any worn-out table inserts.

• Only use saw blades recommended by the

manufacturer (EN-847-1).

• Never use HS (High Speed) saw blades.

• Check that the sawn off bits can be removed

sideways from the saw blade, otherwise they

can get caught on the blade and flung about.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1031 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info