Bedienungsanleitung Ferm MSM1035 (Seite 8 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

634079

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

machine type information must be always

visible on machine.

At the end of the sawing process, keep the saw

head downstairs, switch off the machine and

wait until the all moving parts has come to a stop

before you take your hands off the machine.

3. ASSEMBLY AND

ACCESSORIES

Installation of the mitre saw

• Placeonesidebar(21)ontheright-handside

of the machine and the other sidebar on the

left-hand side of the machine.

• Placetheworkpiececlamp(7)ontheleftor

right side of the machine.

• Holdthehandgripandmovethesawslightly

downwards and then pull the pin (5) out slightly

so that saw moves upwards.

Note: Never use the mitre saw without the

extension pieces supplied. Make sure that they

are correctly mounted.

Mounting the anti-tip over support.

• Mountthesupportbracket(24)intotheslotin

the rear of the base.

• Tightenthescrewstosecurethesupport

bracket.

Sliding fence

Fig.2

For safety reasons, this machine is equipped with

a moveable guide fence to used in normal and

bevel cutting.

• Fornormalstraightcross-cutsandmitrecuts,

always adjust the sliding fence (8) to the end

and fix well to provide safety support for work

piece.

• Forbevelcuts,adjusttheslidingfence(8)

to a suitable position as close as to the saw

blade surface but avoid interfere the saw blade

movement and ensure to fix well.

Changing the saw blades

Fig. 4 and 5

Only use saw blades that are sharp and

undamaged. You must immediately

replace chipped or bent saw blades.

DANGER: Do not use any blade larger than the

stated capacity of the saw. It may come into

contact with the blade guard and cause harm.

Do not use a blade too thick to allow the outer

blade washer to engage with the flats on the

spindle. This will prevent the blade screw from

securing the blade on the spindle.

Do not use this saw to cut metal or masonry

• Disconnectthemachinefromthepowersupply.

• Removethescrew(20)thatholdstheretraction

arm to the blade cover.

• Removethescrew(19)inordertoremovethe

bolt-cover by lifting the blade cover (6) upwards.

• Bothsawbladebolt(17)andFlange(18)should

be visible now like shown in fig. 5.

• Pressthesawbladelockbutton(22)Rotatethe

saw blade carefully by hand until the blade locks.

• Usehexkeytoremovethesawbladebolt(17)

by loosening in a clockwise direction.

• RemovetheFlange(18)andthesawblade

• Replacethesawblademakingsurethatthe

arrow marked on the saw blade must point in

the same direction as the arrow shown marked

on the machine. The saw blade teeth must point

downwards.

• Fixthesawbladebolt(17)usethesawblade

lock button (22) in order to secure tightly

• Lowerthebladecover(6)inorderforthebolt-

cover to fall back into place and tighten the

screw (19)

• Attachtheretractionarmbackontotheblade

cover (6) by tightening the screw (20)

• Rotatethesawbladeandcheckiftheguard

operates freely

Adjusting the cutting angle

Fig. 2.

Adjusting Mitre Angles

The mitre angle can be set between 45° left side

and 45° right side

• Loosenthelockingknob(10)

• Pressthelockingpaddle(11)andturnthesaw

table left or right by the locking knob (10) until

the angle indicator (23) indicates the required

angle.

• Releasethelockingpaddle(11)andtightenthe

locking knob (10)

Pre-settings (quick settings) on the following

degrees: -45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°,

30°, 45°.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1035 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info