Bedienungsanleitung Ferm MSM1036 (Seite 7 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

562154

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

10. Always lock the different degree set-ups

before you start processing.

11. Only buy suitable saw blades with a number

of revolutions of at least 5.000 revolutions per

minute.

12. Only use the correct saw blade. Too small or

too big saw blades are extremely dangerous.

13. Regularly inspect the saw blade for any faults.

Replace the saw blade if necessary.

14. Grease the new saw blade and clean the

flanges before you assemble the new blade.

Then assemble the blade in the correct

direction and pull the flanges firmly using the

central bolt.

15. Only use original flanges. All other types are

not suitable.

16. Never work without the protective cap of the

saw blade.

17. The moving part of the protective cap must

also remain assembled.

18. Never grease the saw blade while it is

rotating.

19. Always keep your hands removed from the

track of the saw blades.

20. Never pick up the workpiece by grasping with

your hands along or behind the saw blade.

21. Ensure that the workpiece never touches

the saw blade before the machine has been

switched on.

22. Never process metal or stone sorts with this

machine.

23. Use support aids in order to support long

workpieces.

24. Never use the machine in a dangerous

environment, where inflammable gases or

fluids are present.

25. Never leave the machine unattended without

first disconnecting it from the mains voltage.

26. If you hear abnormal noises, try to trace them

or take the machine to a recognized fitter, or

repair company.

27. If a part is broken or damaged, replace it or

repair it immediately.

28. Never stand in the track of the saw blade but

stand to the left or the right of the saw bench.

29. Your hands must likewise be placed next to

the track of the saw blade.

30. Always use the feedstick to push the wood

through the saw.

31. Always place the wood at the front of the saw

bench and then push it further back.

32. For mitring only the adjustable guide must be

used and the fence must be removed.

33. Never use the fence as a linear measure for

cutting off beams.

34. If the saw blade is locked: first switch off the

machine before you attend to the fault.

35. Avoid workpieces hitting back in your direction

by taking the following measures:

• Always use sharp saw blades.

• Do not saw too small workpieces.

• Never release the workpiece before it has

been completely pushed through the saw.

• Always adjust the guide parallel to the

saw blade.

• Never remove the saw protection.

36. Before you continue sawing, ensure that you

are standing firmly and that your hands are in

the required position.

37. Never use thinners to clean the machine. Only

use a damp cloth for cleaning.

38. Do not use saw blades which are damaged or

deformed.

39. Replace table insert when worn.

40. Use only saw blades recommended by the

manufacturer.

41. Take care that the selection of the saw blade

depends on the material to be cut.

42. Connect radial saws to a dust-collecting

device when sawing.

43. Use and correct adjustment of the riving knife

44. Use and correct adjustment of the upper saw

blade quard.

45 The dust that is emitted when sawing certain

types of wood can be toxic, i.s. oak, birch,

ash, beech and fibreboard. Certain dust, from

tropical wood types such as rosewood, coco

bolo and afzelia, cause cancer when breathed

in regularly. Ensure therefore that you have

good dust suction installed with a device that

fulfils the following requirements:

• Tube must fit perfectly on the connection

element

• Suction volume must be larger than 550

m3 per hour

• Vacuum at connection more than 740 Pa

• Air speed at connection more than 20

meters/second

Ensure that the least possible wood dust

is released in the atmosphere. WIPE wood

dust away (do not blow away with pressured

air), repair leaks in the tubes and ensure

appropriate ventilation.

Do not use saw blades which are damaged or

deformed.

Always clamp or press the workpiece firmly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1036 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm MSM1036

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info