Bedienungsanleitung Ferm MSM1036 (Seite 10 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

562154

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Sliding fence

Fig.2

For safety reasons, this machine is equipped with

a moveable guide fence to used in normal and

bevel cutting.

• For normal straight cross-cuts and mitre cuts,

always adjust the sliding fence (8) to the end

and fix well to provide safety support for work

piece.

• For bevel cuts, adjust the sliding fence (8) to a

suitable position as close as to the saw blade

surface but avoid interfere the saw blade

movement and ensure to fix well.

Changing the saw blades

Fig. 4 and 5

Only use saw blades that are sharp and

undamaged. You must immediately

replace chipped or bent saw blades.

DANGER: Do not use any blade larger than

the stated capacity of the saw. It may come

into contact with the blade guard and cause

harm.

Do not use a blade too thick to allow the outer

blade washer to engage with the flats on the

spindle. This will prevent the blade screw from

securing the blade on the spindle.

Do not use this saw to cut metal or masonry

 • Disconnectthemachinefromthepower

supply.

 • Removethescrew(20)thatholdsthe

retraction arm to the blade cover.

 • Removethescrew(19)inordertoremove

the bolt-cover by lifting the blade cover (6)

upwards.

 • Bothsawbladebolt(17)andFlange(18)

should be visible now like shown in fig. 5.

 • Pressthesawbladelockbutton(22)

Rotate the saw blade carefully by hand

until the blade locks.

 • Usehexkeytoremovethesawbladebolt

(17) by loosening in a clockwise direction.

 • RemovetheFlange(18)andthesaw

blade

 • Replacethesawblademakingsurethat

the arrow marked on the saw blade must

point in the same direction as the arrow

shown marked on the machine. The saw

blade teeth must point downwards.

 • Fixthesawbladebolt(17)usethesaw

blade lock button (22) in order to secure

tightly

 • Lowerthebladecover(6)inorderfor

the bolt-cover to fall back into place and

tighten the screw (19)

 • Attachtheretractionarmbackontothe

blade cover (6) by tightening the screw

(20)

 • Rotatethesawbladeandcheckifthe

guard operates freely

Adjusting the cutting angle

Fig. 2.

Adjusting Mitre Angles

The mitre angle can be set between 45° left side

and 45° right side

- Loosen the locking knob (10)

- Press the locking paddle (11) and turn the saw

table left or right by the locking knob (10) until

the angle indicator (23) indicates the required

angle.

- Release the locking paddle (11) and tighten

the locking knob (10)

Pre-settings (quick settings) on the following

degrees: -45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°,

30°, 45°.

- Press the locking paddle (11) when turning

the baseplate, release the paddle before

reaching the requested degrees and the plate

with “click” into the pre-setting itself.

Adjusting Bevel Angles

Fig. 1 and 3

The bevel angle can be set between 0° and 45°.

- Loosen the adjusting knob (9)

- Tilt the saw by using the handle until the angle

indicator (14) indicates the required angle.

- Tighten the adjusting knob (9)

Changing the carbon brushes

Fig. 2

- Disconnect the machine from the power

supply

- Unscrew the two covers (4) on the front and

backside of the motor housing.

- Replace the carbon brushes with the exact

type of brushes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1036 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm MSM1036

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info