Bedienungsanleitung Ferm MSM1037 (Seite 10 von 92) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

634080

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Adjusting the cutting angle

Fig. 2

Adjusting Mitre Angles

The mitre angle can be set between 45° left side

and 45° right side

- Loosen the locking knob (10).

- Turn the saw table left or right until the angle

indicator (23) indicates the required angle.

- Tighten the locking knob (10).

Pre-settings (quick settings) on the following

degrees: -45°, -40°, -35°, -30°, -25°, -20°, -15°,

-10°, -5°, 0°, 5°, 10°, 15°, 20°, 25°, 30°, 35°, 40°,

45°.

Adjusting Bevel Angles

Fig. 1 and 3

The bevel angle can be set between 0° and 45°.

Adjust sliding fence accordingly!

See chapter 3, sliding fence.

- Loosen the adjusting knob (9).

- Tilt the saw by using the handle until the angle

indicator (14) indicates the required angle.

- Tighten the adjusting knob (9).

Changing the carbon brushes

Fig. 2

- Disconnect the machine from the power

supply.

- Unscrew the two covers (4) on the front and

backside of the motor housing.

- Replace the carbon brushes with the exact

type of brushes.

- Tighten the covers (4) again.

Note: Always replace both carbon brushes at the

same time, never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. 1

Press in the clamp of the dust bag (13) and slide

it onto the opening on the back of the machine.

The dust bag stays in place when you release the

clamp.

4. OPERATION

Using the mitre saw

Fig. 1

Before use, always check for faults or

defects!

• Setthedesiredsawingangleofthemachine.

• Puttheplugintothesocket.

• Fixthepieceofworkinplaceusingtheclamp

(7): make sure that the material is well clamped

in place!

• Holdthematerialtightlyontheleftsidewhile

making sure that you keep a safe distance

from the blade of the saw.

• Turnonthemachineusingtheswitch(1).

• Makesurethatthesawbladehasreachedfull

speed before allowing it to touch the piece of

work to be sawn.

• Useknob(3)toraisetheprotectivecoverlock.

• Nowbringthesawslowlydownwardssothat

the saw blade saws through the piece of work

and passes through the slot in the table. Do

not put any pressure on the saw. Give the

machine time to saw through the piece of

work.

• Bringthemachinegentlyupagainandswitch

it off by letting go of the switch (1).

Using the laser

Fig. 2

• Toswitchonthelaser,presstheon/offswitch

• Toswitchoffthelaser,releasethe

on/off switch 2.

5. SERVICE AND MAINTENANCE

Always make sure that the machine is not

connected to the mains electricity when

you carry out any maintenance of the

mechanism.

Cleaning

Clean the machine housing regularly with a soft

cloth, preferably after each time you use the

machine. Make sure that the ventilation slots are

free of dust and dirt. For stubborn dirt use a soft

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1037 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info