Bedienungsanleitung Ferm MSM1038 (Seite 9 von 132) (Alle Sprachen)

697796

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

• Press the locking paddle (11) when turning the

baseplate, release the paddle before reaching

the requested degrees and the plate with

“click” into the pre-setting itself.

Adjusting Bevel Angles

Fig. 1 and 3

The bevel angle can be set between 0° and 45°.

• Loosen the adjusting knob (9)

• Tilt the saw by using the handle until the angle

indicator (14) indicates the required angle.

• Tighten the adjusting knob (9)

Changing the carbon brushes

Fig. 2

• Disconnect the machine from the power

supply

• Unscrew the two covers (4) on the front and

backside of the motor housing.

• Replace the carbon brushes with the exact

type of brushes

• Tighten the covers (4) again.

Note: Always replace both carbon brushes at the

same time, never use a mixture of old and new

brushes.

Mounting the dust bag

Fig. 1

Press in the clamp of the dust bag (13) and slide

it onto the opening on the back of the machine.

The dust bag stays in place when you release the

clamp.

4. OPERATION

Using the mitre saw

Fig. 1

Before use, always check for faults or

defects!

• Set the desired sawing angle of the machine.

• Put the plug into the socket.

• Fix the piece of work in place using the clamp

(7): make sure that the material is well clamped

in place!

• Hold the material tightly on the left side while

making sure that you keep a safe distance

from the blade of the saw.

• Turn on the machine using the switch (1).

• Make sure that the saw blade has reached full

speed before allowing it to touch the piece of

work to be sawn.

• Use knob (3) to raise the protective cover lock.

• Now bring the saw slowly downwards so that

the saw blade saws through the piece of work

and passes through the slot in the table. Do

not put any pressure on the saw. Give the

machine time to saw through the piece of

work.

• Bring the machine gently up again and switch

it off by letting go of the switch (1).

Using the slide-function

Fig. 1

The machine must be firmly bolted to a

workbench.

Use the slide-function for sawing wide

workpieces:

• Fix the piece of work in place using the clamp

• Loosen the knob (12)

• Slide the machine completely towards yourself

• Turn on the machine using the switch

• Bring the saw slowly downwards so the saw

blade saws through the piece of work

• Push the machine slowly backwards

• Bring the machine gently up again and switch

it off by letting go of the switch

Using the laser

Fig. 2

• To switch on the laser, press the on/off switch 2.

•

To switch off the laser, release the on/off switch 2.

Transport position

When moving the saw, make sure the saw is

in inward position. Check that all locks and

tensioning devices are secure:

• Make sure the mitre angle is set to 0°

• Make sure the bevel angle is set to 0°

• Lock the Knob adjusting saw angle (9) by

turning it clockwise

• Slide the machine completely towards yourself

• Lock the sliding function by turning Kob over

sliding support (12) clockwise

• Unlock the Lock pin (5) on the right hand side

of the machine

• Use knob (3) to raise the protective cover lock

• Push the machine completely downwards

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1038 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info