Bedienungsanleitung Ferm MSM1039 (Seite 8 von 108) (Alle Sprachen)

697795

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

• Place the work piece clamp (7) on the left or

right side of the machine.

• Hold the handgrip and move the saw slightly

downwards and then pull the pin (5) out slightly

so that saw moves upwards.

Note: Never use the mitre saw without the

extension pieces supplied. Make sure that they

are correctly mounted.

Sliding fence

Fig.2

For safety reasons, this machine is equipped with

a moveable guide fence to used in normal and

bevel cutting.

• For normal straight cross-cuts and mitre cuts,

always adjust the sliding fence (8) to the end

and fix well to provide safety support for work

piece.

• For bevel cuts, adjust the sliding fence (8)

to a suitable position as close as to the saw

blade surface but avoid interfere the saw blade

movement and ensure to fix well.

Changing the saw blades

Fig. 4 and 5

Only use saw blades that are sharp and

undamaged. You must immediately

replace chipped or bent saw blades.

DANGER: Do not use any blade larger than the

stated capacity of the saw. It may come into

contact with the blade guard and cause harm.

Do not use a blade too thick to allow the outer

blade washer to engage with the flats on the

spindle. This will prevent the blade screw from

securing the blade on the spindle.

Do not use this saw to cut metal or masonry.

• Disconnect the machine from the power supply.

• Remove the screw (20) that holds the retraction

arm to the blade cover.

• Remove the screw (19) in order to remove the

bolt-cover by lifting the blade cover (6) upwards.

• Both saw blade bolt (17) and Flange (18) should

be visible now like shown in fig. 5.

• Press the saw blade lock button (22) Rotate the

saw blade carefully by hand until the blade locks.

• Use hex key to remove the saw blade bolt (17)

by loosening in a clockwise direction.

• Remove the Flange (18) and the saw blade

• Replace the saw blade making sure that the

arrow marked on the saw blade must point in

the same direction as the arrow shown marked

on the machine. The saw blade teeth must point

downwards.

• Fix the saw blade bolt (17) use the saw blade

lock button (22) in order to secure tightly

• Lower the blade cover (6) in order for the bolt-

cover to fall back into place and tighten the

screw (19)

• Attach the retraction arm back onto the blade

cover (6) by tightening the screw (20)

• Rotate the saw blade and check if the guard

operates freely

Adjusting the cutting angle

Fig. 1-2.

Adjusting Mitre Angles

The mitre angle can be set between 45° left side

and 45° right side

• Loosen the locking knob (10)

• Press the locking paddle (11) and turn the saw

table left or right by the locking knob (10) until

the angle indicator (23) indicates the required

angle.

• Release the locking paddle (11) and tighten the

locking knob (10)

Pre-settings (quick settings) on the following

degrees: -45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°,

30°, 45°.

• Press the locking paddle (11) when turning the

baseplate, release the paddle before reaching

the requested degrees and the plate with

“click” into the pre-setting itself.

Adjusting Bevel Angles

Fig. 1 and 3

The bevel angle can be set between 0° and 45°.

• Loosen the adjusting knob (9)

• Tilt the saw by using the handle until the angle

indicator (14) indicates the required angle.

• Tighten the adjusting knob (9)

Changing the carbon brushes

Fig. 2

• Disconnect the machine from the power

supply

• Unscrew the cover (4).

• Replace the carbon brushes with the exact

type of brushes

• Tighten the cover (4) again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1039 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info