4.
/
. D
•
().
(A)
.
•
, , (B).
,
().
•
0 -2500 ,
(A)
.
•
().
• ()
().
• ,
()
.
• :
() “L”.
• :
() “R”.
. E
.
• ,
“”.
• ,
“”.
,
:
1.
•
.
Ferm.
2. .
• .
.
• .
.
!.
• .
Ferm .
5.
"# $
$$ !
.
Ferm
.
.
,
.
.
,
.
,
, ..
.
.
..
,
Ferm.
,
.
,
.
.
.
Ferm. ,
.
% /
.
Ferm 57
Also use face or dust mask when operation is dusty.
10. Connect dust extraction equipment
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
11. Do not abuse cord.
Never carry tool by cord or yank it to disconnect it from
electrical socket. Keep cord from heat, oil and sharp
edges.
12. Secure work.
Use clamps or a vice to hold work. It’s safer than using
your hand and it frees both hands to operate tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically and,
if damaged, have repaired by authorized service facility.
Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean and free from oil and
grease.
15. Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
17. Avoid unintentional starting.
Do not carry plugged-in tools with finger on switch. Be
sure switch is off when plugging in.
18. Outdoor use extension cords.
When tool is used outdoors, use only extension cords
intended for use outdoors and so marked. Always use tool
in conjunction with a residual circuit breaker device.
19. Stay alert.
Watch what you are doing. Use common sense. Do not
operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it
will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorized service centre unless otherwise
indicated elsewhere in this instructions manual. Have
defective switches replaced by an authorized centre. Do
not use tool if switch does not turn on and off.
21. Warning.
The use of any other accessory or attachment other than
recommended in this operation instructions or the
catalogue may present a risk of personal injury.
22. Have your tool repaired by an expert.
This appliance is manufactured to very high standards and
meets relevant safety regulations. Repairs should only be
done by a suitable qualified electrical engineer or
otherwise.
23. Hearing protection should be worn.
ELECTRICAL SAFETY
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Keep these instructions in a safe place!
Always check that the power supply corresponds to
the voltage on the rating plate.
Your machine is double insulated in accordance
with EN 50144; therefore no earthwire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm2. When using a cable reel always unwind
the reel completely.
BEFORE OPERATING THE MACHINE:
•Check the following:
Do the voltage of the machine correspond with the
mains voltage
Are the mains lead and the mains plug in a good
condition.
•Do not use extension cables which are too long. Use
extension cables with a core diameter of 1.5 mm2
minimal and only when the cable is rolled out
completely.
•In case of a blockage, switch of the machine
immediately.
•Always compare the maximum rotation speed of
accesoires with the maximum speed of the
percussion drill.
•Pull the mainsplug from the socket before you
change a drill or accessory.
WHEN OPERATING THE MACHINE:
•Check if the switch is placed in the ‘OFF’-position
before you connect the machine to mains.
•Keep the mains cable away from moving parts of the
machine.
•First switch off the machine before you move the
machine downwards along your body.
•Never cover the ventilation slots.
IMMEDIATELY SWITCH OFF THE
MACHINE IN CASE OF:
•Excessive sparking of the brushes and verticiliosis in
the collector.
•Malfunction of the mainsplug, -socket or damaged
cables.
•Broken switch.
•Smoke or smell caused by scorched insulation.
4Ferm
