Bedienungsanleitung Ferm PDM1045P-A (Seite 5 von 20) (Englisch, Französisch)

763928

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Removing

• Place the chuck key (10) into one of the holes

in the chuck (1).

• Open the chuck (1) by turning the chuck key

(10) counterclockwise.

• Remove the drill bit (11) from the chuck (1).

• Close the chuck (1) by turning the chuck key

(10) clockwise.

• Remove the chuck key (10) from the chuck (1).

Setting depth stop

Fig. C

• Insert the depth stop (3) in the hole in the side

handle ring.

• Slide the ruler to the desired depth.

The On/Off switch

Fig. A

• Switch the machine on by pressing the On/Off

switch (5). When you release the On/Off switch

(5) the machine will turn off.

• The rotation-speed can be adjusted by

pressing the On/Off switch (5) harder for

raising the rotation-speed or release pressure

for lowering the rotation-speed.

Lock-on Button

Fig. A

• You can lock the On/Off switch (5) by pressing

the On/Off switch (5) and then pressing the

lock-on button (4).

• To release the switch-lock; shortly press the

On/Off switch (5) again.

Adjusting of the maximum rotation speed

Fig. A

• Adjust the speed by turning the speed

adjustment wheel (6) to the desired maximum

rotation speed.

Switching the direction of rotation

Fig. A

Do not change the direction of rotation

during use.

• Direction of rotation counter-clockwise: shift

left/right rotation switch (7) to “ ”.

• Direction of rotation clockwise: shift left/right

rotation switch (7) to “ ”.

Function selection switch

Fig. A

In order to avoid damage to the machine,

adjusting the function selection switch (2)

shall only be done when machine is not

running

• Set the function selection switch (2) to “ ”

for drilling.

• Set the function selection switch (2) to “ ”

for hammer drilling.

Gear selection switch

Fig. A

In order to avoid damage to the machine,

adjusting the gear selection switch (8)

shall only be done when machine is not

running.

• If you set the gear selection switch (8) to

position “1”, the drilling speed can be adjusted

between 0 and 1,000 /min.

• If you set the gear selection switch (8) to

position “2”, the drilling speed can be adjusted

between 0 and 2,800 /min.

• When the gear selection switch (8) cannot

switch easily between “1” and “2”, give the

chuck (1) a little spin by using your hands. This

will help the gears fall into the correct position

and makes switching the gears easier.

User tips

Always use the machine with the side handle

firmly anchored in place - you will not only work

with more comfort, you will also work with more

precision.

Caution: drilling bits and hammer drilling

bits can get very hot

Drilling and hammer drilling

• For large holes, for instance in very hard

concrete, start using a smaller bit for pilot

drilling first , then drill to nominal size.

• Hold the machine firmly with 2 hands. Be

aware the drill can jam and because of that

machine might suddenly turn (Especially when

drilling deep holes).

• Do not apply a lot of pressure on the machine,

let the machine do the work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PDM1045P-A Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info