762259
6
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
6
EN
ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Exchanging and removing drill bits
Fig. A - B
The machine is suitable for use of the following
drill bits:
Wood (HSS)
Metal (HSS)
Concrete / masonry (hard metal)
Before exchanging bits, first remove the
power plug from the wall socket.
Inspect bits regularly during use. Blunt
bits should be re-sharpened or replaced.
Open the chuck (6) by turning the front
sleeve (11) clockwise while simultaneously
holding the rear sleeve (10) or turning it
counterclockwise and insert the bit into the
chuck opening.
Tighten the bit by turning the front sleeve (11)
counterclockwise while simultaneously
holding the rear sleeve (10) or turning it
clockwise.
Mounting and removing the auxiliary grip (fig.C)
Mounting
Loosen the auxiliary grip (8).
Slide the auxiliary grip (8) over the chuck (6).
Turn the auxiliary grip (8) to the required
position.
Tighten the auxiliary grip (8).
Removing
Loosen the auxiliary grip (8).
Remove the auxiliary grip (8) from the chuck (6).
Tighten the auxiliary grip (8).
Mounting and removing the depth stop (fig. D)
The depth stop is used to set the maximum
drilling depth.
USE
Switching on and off (fig. A)
To switch on the machine, press the on/off
switch (1). The further the on/off switch (1) is
pressed, the higher the speed of the machine.
To switch the machine to continuous mode,
keep the on/off switch (1) pressed and
simultaneously press the lock-on button (2).
To switch off continuous mode, press the on/
off switch (1) again.
Forward/reverse switch (fig. A)
Do not change the direction of rotation
during use.
For clockwise rotation, slide the forward/
reverse switch (4) to the left.
For counterclockwise rotation, slide the
forward/reverse switch (4) to the right.
Setting the maximum drilling speed (fig. A)
Do not set the speed during use.
Turn the speed adjustment wheel (3) clockwise
to increase the maximum drilling speed.
Turn the speed adjustment wheel (3)
counterclockwise to decrease the maximum
drilling speed.
Setting the operating mode (fig. E)
Do not change the operating mode
during use.
Set the switch (5) to position ”A” for drilling.
Set the switch (5) to position ”B” for hammer
drilling.
CLEANING AND MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
Regularly clean the housing with a soft cloth.
Keep the ventilation slots free from dust and
dirt. If necessary, use a soft, moist cloth to
remove dust and dirt from the ventilation slots.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ferm PDM1052 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info