Bedienungsanleitung Ferm PPM1010 (Seite 5 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

510112

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Ferm

Parts list

Fig. 1 + 2

1. Control knob for adjustment of planing depth

2. Indication of planing depth

3. Operating Switch

4. Release Button

5. Handle

6. Cover, left

7. Planer shoe with V-groove

8. Dustbag connection

2. SAFETY INSTRUCTIONS

Explanation of symbols

Denotes risk of personal injury, loss of

life or damage to the tool in case of non-

observance of the instructions in this

manual.

Indicates electrical shock hazard.

Wear ear and eye protection

Wear a dust mask

Switch off the machine immediately in case of:

• Malfunctioninthemainsplug,powercableor

damaging of cable.

• Brokenswitch.

• Smokeorstenchofscorchedinsulation.

Wait for the cutter to stop before setting

the tool down. An exposed cutter may

engage the surface leading to possible

loss of control and serious injury.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions. Keep these

instructions in a safe place!

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class ll machine. Your machine is

double insulated; therefore no earthwire

is required.

When replacing old cables or plugs

Throw away old cables or plugs immediately as

soon as new ones have replaced these. It is

dangerous to put the plug of a loose cable into the

socket outlet.

When using extension cables

Only use an approved extension cable that is

suitable for the machine’s power. The cores must

have a diameter of at least 1.5 mm2. When the

extension cable is on a reel, unroll the cable in its

entirety.

3. OPERATION

Before setting up, repair or maintenance

of the appliance you must always turn

off the operating switch and pull out the

mains plug!

Before initial operation

• Check if the rated voltage and rated frequency

of the mains supply correspond to the details

of the type plate.

• Place the workbench on a stable and even

base.

Operation

Fig. 1

• To adjust the planing depth, turn the control

knob (1) in a clockwise direction. On the

control knob there is a pointer which shows

the planing depth in mm. Turn the control knob

until the desired planing depth is shown.

Never alter the planing depth during an

operating cycle, otherwise this will result

in an uneven surface. To prevent

operating errors turn the control knob

back to “0” when planing is completed.

• Secure the work piece with clamps or similar.

• Place the front sole on the edge of the work

piece in such a way that the planing tool does

not yet touch the work piece. The work piece

must be level.

Switching on and off

• This machine is equipped with a safety switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PPM1010 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info