Bedienungsanleitung Ferm PRM1015 (Seite 7 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510113

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Material Diameter

Router bit

Speed stages

Hardwood >20 mm 1 – 2

10 – 20 mm 3 – 4

<10 mm 5 – max

Softwood >20 mm 1 – 3

10 – 20 mm 3 – 6

<10 mm 5 – max

Aluminium >15 mm 1

<15 mm 1 – 2

Plastic >15 mm 1 – 2

<15 mm 2 – 3

After longer periods of working at low speed,

allow the machine to cool down by running it for a

few minutes at high speed with no load

Height setting of the router column

Fig. G+A1

The clamping lever (11) is used to set the

maximum height of the router.

Theplungedepthisthenxed.Thisisusually

necessary when using the tool on a special router

table.

Make sure the router column is not locked.

The router can be pushed down against the

spring force.

Lock the router column using the clamping lever

The router is now locked and will no longer return

to its original position.

Setting the plunge depth

Fig. G+A1

The plunge depth can be adjusted by using

buttons8,9,11and15.Iftheplungedepthisset

correctly, the groove in question can be routed

accurately to within 0.1 mm.

Preparation:

• Placethedesiredcutterinthetool.

The router can be pushed down against the

spring force.

• Pushthetooldownuntilthecuttertouchesthe

workpiece, then lock it using the clamping

lever (11).

• Loosenbutton9.

• Setbutton15tozero.

• Usebutton8tosetthedepthalltheway

down.

• Tightenbutton9(clockwise).Theplungedepth

is now set to precisely 0 mm.

Rough setting:

• Readthevaluefromthescale(12).

• Loosenbutton9.

• Turnbutton8andre-readthevaluefromthe

scale. The difference between the two values

istheplungedepthsetting.Forexample:Ifthe

value on the scale (12) is 8.5 in the zero-

setting and the value is 7.0 after button (8) has

been turned, then the plunge depth has been

set to 1.5 cm.

• Retightenbutton9.

Fine adjustment:

• Loosenbutton9.

• Thetopbutton(15)isstillsettozero.Givethis

button a full counter-clockwise turn, until it is

back in the zero position. The plunge depth is

now 1.0 mm less.

• Ifrequired,theplungedepthcanbeset

accurately to within 0.1 mm.

• Retightenbutton9.

Unlock the clamping lever (11)

Adjustment using the revolver- depth stop

The revolver-depth stop enables you to quickly

choose between three different cutting depths.

These are also determined by the adjustment of

the depth stop (10).

For larger routing depths, it is recommended to

carry out several repetitive cuts with lower

removal rates.

• Adjusttherequiredcuttingdepthbyrotating

the revolver-depth stop (21).

5. MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

These machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PRM1015 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info