Bedienungsanleitung Ferm PRM1021 (Seite 7 von 128) (Alle Sprachen)

762275

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

After longer periods of working at low speed,

allow the machine to cool down by running it for a

few minutes at high speed with no load

Height setting of the router column

Fig. B

The clamping lever (10) is used to set the

maximum height of the router.

The plunge depth is then fixed. This is usually

necessary when using the tool on a special router

table. Make sure the router column is not locked.

The router can be pushed down against the

spring force. Lock the router column using the

clamping lever The router is now locked and will

no longer return to its original position.

Adjusting the routing depth

• Place the machine on the workpiece.

• Undo the wing screw (8) and fixing handle (10).

• Slowly move the machine downwards until the

cutter makes contact with the workpiece.

• Tighten the fixing handle (10).

• Set the depth stop (9) to the required routing

depth using the scale and secure it with the

wing screw (8).

• Test the setting by completing a test cut on a

waste piece.

Adjustment using the revolver- depth stop

The revolver-depth stop enables you to quickly

choose between six different cutting depths.

These are also determined by the adjustment of

the depth stop (9).

For larger routing depths, it is recommended

to carry out several repetitive cuts with lower

removal rates.

• Adjust the required cutting depth by pressing

the revolver-depth stop downwards and

rotating the revolver-depth stop (16).

Using the centre pin

Fig. G

• To use the centre pin, insert one guide rod (15)

with the centre pin (20) attached into the holes,

either side of the base plate of the router.

• Secure the guide fence rod to the router at the

required length be rotating the fixing screw (4)

clockwise.

5. MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

These machines have been designed to operate

over a long period of time with a minimum of mainte-

nance. Continuous satisfactory operation depends

upon proper machine care and regular cleaning.

Cleaning

Regularly clean the machine housing with a

soft cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt. If the dirt

does not come off use a soft cloth moistened with

soapy water. Never use solvents such as petrol,

alcohol, ammonia water, etc. These solvents may

damage the plastic parts.

Troubleshooting

Please find some potential causes and solutions

to possible failure.

1 The operating switch is switched on, but

the motor is not working

• The electric circuit is broken

• Have the electric circuit repaired

• Wires in the mains plug or in the socket are

loose

• Have socket and plug checked or repaired

• The switch is faulty

• Have the switch repaired

• Carbon brushes are worn

• Replace the carbon brushes

2 Router runs slowly

• Variable speed set low

• Increase variable speed

• Motor is overloaded

• Reduce pushing force on router

3 Excessive vibration

• Bent cutter shank

• Replace cutter

Faults

Should a fault occur, e.g. after wear of a part,

please contact the adress on the warranty card.

Included you find an exploded view showing the

parts that can be ordered.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PRM1021 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info