Bedienungsanleitung Ferm SGM1012 (Seite 7 von 120) (Alle Sprachen)

762273

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

4. MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Troubleshooting

1. Motor hums but does not spray or irregular

spraying

• Worn swirl head.

- Replace swirl head.

• Pick up pipe not in the right position.

- Re-adjust pick up pipe.

• Blocked pick up pipe.

- Clean with thinner.

• Blocked nozzle.

- Clean nozzle.

• Blocked filter.

- Clean with thinner.

• Control knob needs adjustment.

- Adjust.

2. Atomization is not good

• Volume adjustment is not correct.

- Adjust.

• Paint too thick.

- Check viscosity of the paint.

3. Over painting

• Spray gun not clean, or not lubricated,

resulting in piston being stuck in cylinder.

- Disassemble spray gun and clean with thinner.

• Too much paint.

- Adjust the volume clockwise to reduce

spraying. Two thin coats are better then one

thick coat.

• Viscosity too low.

- Check viscosity.

4. Motor louder than normal

• Spray gun not clean, or not lubricated,

resulting in piston being stuck in cylinder.

- Disassemble spray gun and clean with thinner.

5. No spray, no sound

• No electricity.

- Check power supply.

6. Operating sound not right

• Poor output adjustment.

- Re-adjust.

• Not enough paint in the container resulting in

air being sucked in.

- Refill with paint.

• Not diluting properly or not passing pick up

pipe completely.

- Check pick up pipe and viscosity level.

7. “Orange Skin” excessive fogging

• Incorrect solvent is used.

- Use correct solvent.

• Spray gun too far from the surface.

- Hold spray gun closer to the object.

• Paint too thick.

- Thin the paint.

Cleaning and maintenance

Fig. G

Always remember to disconnect from the

mains supply before cleaning the spray

gun or paint container.

It is essential that the spray gun is cleaned

thoroughly after every use. Failure to clean it will

almost certainly result in blockages and it may

not operate when you next come to use it! The

guarantee does not cover cleaning a sprayer that

has not been properly cleaned by the user. The

following action must be taken after every use:

• Empty any remaining material from the

container.

• Clean the container thoroughly with the thinner

thatwas used.

• Pour some thinner into the container and spray

through the spray gun until only clean thinner

is coming out of the nozzle.

• Thoroughly clean the paint pick up pipe and

filter with thinner.

• Clean the basket and nozzle and remove any

other debris or paint that remains.

• Turn the spray gun upside down and apply a

few drops of light oil to the two apertures (F).

This will lubricate the piston and cylinder.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SGM1012 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info