Bedienungsanleitung Ferm SGM1013 (Seite 6 von 104) (Alle Sprachen)

762322

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

the desired temperature setting (ranging from

160°C to 500°C)

• Wait until the soldering tip has reached the

selected temperature. Test the tip temperature

by touching it with solder. The tip is hot enough

when the solder melts away easily.

• Press the terminal pin strongly against the

parts which are to be soldered so that these

are heated. Ensure that the pin presses against

the greatest possible surface area of the parts.

Heat transfer is then at its greatest.

• Hold the tin solder wire at a safe distance so

that you do not burn your fingers. Then pass

the tin solder wire between the tip and the

parts which are to be soldered.

• If the parts have been heated sufficiently, melt

the tin solder and run it into the space between

the parts which are to be joined together.

• Remove the pin from the parts which are to be

joined together but without moving these and

wait until the joint has cooled down and set

(approx. 10 seconds.).

• If the joint has been soldered well, then you will

obtain a polished, shiny surface.

• Clean the soldering tip on the sponge after

each soldering.

• Place the soldering iron back in its holder,

switch off and unplug from the mains after use.

• Let the soldering iron cool down, store away in

a dry place.

Warning: This tool must be placed on its

stand when not in use.

Below, we give you some examples of poorly

soldered joints:

• If the soldering tin is tear-shaped, the soldering

coagulate was too cold.

• If the soldering tin is dull and slightly porous

or crystalline, the parts were probably moved

during the cooling process.

• If too little soldering tin has been left in the

joint, the soldering was too warm or the

soldering tin was not melted sufficiently.

• If the soldering tin is yellow or black, this

means that too much soldering paste has been

used or that the inner core of the tin solder wire

has become overheated during soldering. You

must avoid this above all in electronic circuits

since most acid pastes are corrosive and

reduce the service life of electronic wiring.

Replacement of the soldering tip

Pull out the mains plug!

• Switch off the soldering station and disconnect

from the mains. Let the soldering iron and

tip cool down to room temperature before

handling.

• Unscrew the fixing nut (2). Pull out the tip (1)

from the soldering iron (3) and remove any

oxide that may have formed on the barrel. Be

careful to avoid getting dust in your eyes.

• Replace the tip (1) with another tip and screw

the fixing nut (2) assembly onto the iron (3)

using only hand pressure to tighten. Do not

apply excessive pressure to avoid damage.

4. SERVICE & MAINTENANCE

Repairs may only be carried out by a

qualified electrician or at a service

workshop!

These machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly clean

the machine housing with a soft cloth, preferably

after each use. Keep the ventilation slots free from

dust and dirt. If the dirt does not come off use a

soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water,

etc. These solvents may damage the plastic parts.

Lubrication

The machine requiers no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SGM1013 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info