Bedienungsanleitung Ferm TCM1010 (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

510125

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

6 Ferm

replaced.

• Type of disk: a diamond blade with a diameter

of 180mm.

• Do not use diamond blades that do not meet

the specifications in these instructions.

• Ensure that the diamond blade is secured

properly and rotates in the correct direction.

• To replace a worn disk, please take the

following steps (Fig. 2).

Disconnect the plug from the socket.

• Remove the water tray (4, Fig. 1) from the

machine.

• Loosen the splash guard’s fixing bolts and

remove the splash guard.

• Loosen the blade fixing nut (4, Fig. 2).

• Remove the counter flange (3, Fig. 2) and

blade (2, Fig. 2) and push the new blade on

the flange (1, Fig. 2). Consider the rotation

direction indicated on the blade. Attach the

counter flange (3, Fig. 2).

• Tighten the fixing nut (4, Fig. 2) and the splash

guard.

• Ensure you do not leave any tools lying on the

splash guard.

5. Service & maintenance

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine.

Regularly clean the machine housing with a soft

cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt.

If the dirt does not come off use a soft cloth

moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc.

These solvents may damage the plastic parts.

Please clean the tool immediately after use.

Disconnect the plug from the socket.

• Remove the water tray from the machine and

drain the dirty water.

• Unscrew the splash guard and clean it.

• Loosen the star-shaped knob, fold up the

table, and polish the entire machine.

The machine complies with all current safety

regulations. Repairs may only be carried out by an

approved company, because repair attempts by

unqualified people may cause injuries to the user

and bystanders. Regularly check the plug and the

cable and if they are damaged they should be

replaced by an approved company. Also check

any extension cables. Damaged safety guards

and switches must be replaced before the

machine is used again.

Lubrication

The machine requiers no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. In the back of this manual you find

an exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material. Therefore please

make use of options for recycling the packaging.

Faulty and/or discarded electrical or

electronic apparatus have to be collected

at the appropriate recycling locations.

Warranty

The guarantee conditions can be found on the

separately enclosed guarantee card.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TCM1010 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TCM1010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info