Bedienungsanleitung Ferm TCM1011 (Seite 4 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

510126

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Specific safety instructions

• Check your powertool for damage before

starting your work, particularly the diamond

blade. All parts must be fitted properly and

must meet all requirements in order to

guarantee the tool’s smooth operation. Any

safety guards or any lightly damaged parts

must be checked to see if they still function

properly before continuing the use of the tool.

Moving parts, and the diamond-blade guard in

particular, must be fitted properly and must not

jam. Do not use tools that cannot be switched

on or off with the switch.

• The diamond-blade guard must not be

jammed or removed.

• A jamming guard must be repaired

immediately.

• The riving knife must not be removed.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Connecting to the power supply

Check that the power supply and plug used in

accordance with tour tool. Have a look at the rating

plate on the tile cutter. Any changes should always

be carried out by a qualified electrician.

We strongly recommend the use of an

RCD (Residual Current Device) of not

more than 30 mA, at the plug socket

when using this appliance.

Warning! This machine must be earthed.

If not properly earthed this machine can cause an

electrical shock. Be sure that the power supply

outlet is earthed. If there is any doubt, have it

checked by a qualified electrician.

Warning! Avoid contact with the

terminals on the plug when installing

(removing) the plug to (from) the power

supply outlet. Contact will cause a severe

electrical shock.

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in the

wall outlet.

Using extension cables

Only use an approved extension cable suitable for

the power input of the machine. The minimum

conductor size is 1.5 mm

. When using a cable

reel always unwind the reel completely.

3. ASSEMBLY

Assembly

Fig.1

• Mounting the riving knife.

• Unscrew the two (crosshead) screws (9) and

place the foot of the riving knife (10) under the

table.

• Place the small plate (2 holes with thread)

under the foot of the riving knife.

• Connect the riving knife with the two screws

and the plate.

• Mounting the saw blade.

• Unscrew two screws out of lower blade guard

and remove the guard.

• Dismount nut (counterclockwise) and outer

flange .

• Place blade on the inner flange.

• Mount outer flange and nut (clockwise) again.

• Place the lower blade guard back in position

and connect the two screws.

• Mounting the upper blade guard (11).

• Slide the guard in horizontal position across

the riving knife.

• Connect the guard to the riving knife with the

bolt (12) and the locknut.

• Be aware that the guard is connected under

the lock-pin (13). The lock-pin prevents the

guard falling backwards.

• Mounting the adjustable fence

• Connect the knob (7) with the fence (3) by

using the plate (1 hole with thread); do not

tighten the knob yet.

• Slide the complete fence with (loosen) knobs

onto the table; the plates on the inner side of

the table.

• Set the required distance.

• Tighten the knobs by rotating them

(clockwise).

• Place the water tank (4) under the table.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TCM1011 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TCM1011

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info