Bedienungsanleitung Ferm TDM1025 (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

632651

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Ferm

• Sincethedrillspindleisgreasedinthefactory,

it is advisable to run in the machine for

approximately 15 minutes at the lowest speed.

Before you push the chuck with pin (9)

into the drill spindle, the inside of the

chuck must be completely grease-free!

Setting up the bench drill

Before use the drill must be mounted on a fixed

base. The footplate (13) has therefore been

provided with drilling holes. By means of screws

the footplate can be fixed to the base in this place.

Ifitismountedonawoodenboard,sufficiently

large washers must be used on the opposite side,

so that the bolts are not pushed into the wood and

the machine cannot become loose.

The fastening screws may be fastened so

far that the footplate is not under tension

or deformed. When the tension is too high

there is a risk of breakage.

Adjusting the number of revolutions of the

drill spindle

Fig. C

The different revolutions of the drill spindle can be

adjusted by shifting the V-belt into the belt drive.

The machine is protected by a safety switch so

that the machine is automaticly switched off when

opening the casing. The V-belt is shifted as

follows:

• OpentheV-beltcover(14)byloosenthe

screw on the right side of the cover.

• Loosenthefasteningbutton(18)andslidethe

engine in the direction of the machine head,

upon which the V-belt is released.

• ShifttheV-beltaccordingtothetableonthe

inside of the V-belt cover.

• TensiontheV-beltagainbypushingthe

engine plate (17) to the back. Then the

tensioning device is fastened with the

fastening button (18).

• ClosetheV-beltcoverandthemachineis

ready again for use.

Keep the V-belt cover closed during use.

Fig. C & D

IfyouhaveshiftedtheV-belt,youmusttightenit

again by means of the engine plate (17) with the

fastening button (18). The tension is correct when

the V-belt can be pressed in by approximately 1

cm. The engine pulley must be aligned

horizontally, so that early wear and loosening of

the V-belt can be prevented. For this purpose the

engine pulley (15) on the engine can be slid along

the engine axle, after loosening the socket head

screw.

Spindle speeds

Fig. E

Position V-belt Revolutions/min

1 2650

2 1650

3 1220

4 850

5 580

The number of revolutions of the drill spindle of the

V-belt combinations can be read from the

illustration and the table.

Drill spindle and drill head pin

All the blank parts of the machine are provided

with a protective lacquer layer, which prevents rust

formation. This protective lacquer layer is easy to

remove by means of environmentally friendly

solvents. Test the V-belt tension before you

connect the machine to the electricity mains. The

inside of the drill spindle must be degreased

completely. For this purpose use environmentally

friendly solvents. Proceed in the same way with

the drill head pin. A correct transmission can only

be achieved in this way.

4. Operation, hints and tips

Depth stop

Thedrillspindleisprovidedwithadepthstop.It

can be adjusted using the nut. The drill depth can

be read on the scale division.

Clamping the drill

Fig. F

Inthedrillheadofthebenchdrill,drillsandother

tools with a cylindrical shank can be clamped. The

moment of rotation is transferred to the drill by

means of the tension of the three clamping jaws.

To prevent the drill from sliding away, it must be

clampedusingthetoothedringwrench.Ifthedrill

slides away in the drill holder, a slight burr occurs

on the drill shank, which makes centric clamping

impossible. A burr which occurs in this way must in

any case be removed by grinding.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TDM1025 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info