Bedienungsanleitung Ferm TSM1030 (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

510127

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

machine before you attend to the fault.

35. Avoid workpieces hitting back in your direction

by taking the following measures:

• Alwaysusesharpsawblades.

• Donotsawtoosmallworkpieces.

• Neverreleasetheworkpiecebeforeithas

been completely pushed through the saw.

• Alwaysadjusttheguideparalleltothesaw

blade.

• Neverremovethesawprotection.

36. Before you continue sawing, ensure that you

are standing rmly and that your hands are in

the required position.

37. Never use thinners to clean the machine. Only

use a damp cloth for cleaning.

38. Do not use saw blades which are damaged or

deformed.

39. Replace table insert when worn.

40. Use only saw blades recommended by the

manufacturer.

41. Take care that the selection of the saw blade

depends on the material to be cut.

42. Connect circular saws to a dust-collecting

device when sawing.

43. Use and correct adjustment of the riving knife

44. Use and correct adjustment of the upper saw

blade quard.

45. Take care when slotting.

Before use, remove the transport protection:

• Disassemble the bottom plate by loosening the

4 screws.

• Remove the transport protection below motor.

• The handles for height and mitre setting of the

saw blade are located in the transport

protection inside the machine.

• Reassemble the bottom plate.

Switch off the machine immediately when you

discover:

• A defective mains plug or mains lead.

• A defective switch.

• Overheating of the machine.

• Smoke or odeur caused by scorched

insulation.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of re, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Alwayscheckthatthepowersupply

corresponds to the voltage on the rating

plate.

Replacing cables or plugs

Immediately throw away old cables or plugs when

they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

• As a supply for this machine always use an

unloaded line and/or an extension cable with

conductors of at least 1,5 mm

and protected

with a 16 A fuse. Be sure that this extension

cable is not longer than 20 metres.

• Only connect your machine and/or extension

cable to an earthed electricity mains.

• This machine can be switched to the single-

phase network (230 V/50 Hz). If you are in

doubt about the earth of the electricity

provisions, consult an electrician rst.

3. ASSEMBLY INSTRUCTIONS

Installation of the machine on a workbench or

on the subframe

This machine is a stationary machine and for

safety reasons must always be rmly installed

and not used for mobile applications.

You can install the machine in two ways:

a. As a stationary machine on a workbench. In

this case the machine must be secured to the

workbench with 4 bolts.

b. As a stationary machine on the subframe. In

this case the machine must be secured to the

subframe with 4 bolts and the subframe

anchored to the oor or to a oor plate with

dimensions of at least 1 square metre

Assembly of the bench saw on the workbench

Fig. B & C

Before adjusting the saw, make sure the

plug is removed from the socket.

Fig. B shows the distance of the holes to be

drilled in the workbench on which to fasten the

machine. Drill holes of 8 mm.

Only use the machine after it has been

assembled completely and it has been

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1030 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info