Bedienungsanleitung Ferm TSM1030 (Seite 11 von 52) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

510127

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

operations.

Crosswise sawing with a horizontal mitre

With this method the cross-cut fence must be

secured at the angle required. Keep the

workpiece pressed rmly against the cross-cut

fence and the bench before you start cutting off.

5. MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

These machines have been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon

proper machine care and regular cleaning.

Malfunctions

In the case that the machine is not functioning

properly, we give a number of possible causes

and appropriate solutions below.

1. Working instructions

• The plug is not in the mains.

• The cable has been interrupted.

2. The workpieces is jamming against the

riving knife during processing

• The saw blade must be aligned (Fig. E).

3. The saw cut is not smooth (frayed)

• The saw blade must be sharpened.

• The saw blade has been assembled back-to-

front.

• The saw blade has become coated with resin

or sawdust.

• The saw blade is not suitable for this process.

4. The workpiece is touching the back of the

saw blade and is jumping out

• The riving knife must be aligned (Fig. E).

• The fence is not being used.

• The saw blade is thicker than the riving knife

or the riving knife is not being used

• The saw blade must be sharpened.

• The workpiece has not been kept in its place

until after sawing.

• The tension button of the cross-cut fence is

loose.

5. The height and/or mitre handle is blocked

• Sawdust and dust must be removed.

6. Theenginehasdifcultyreachingthe

maximum number of revolutions

• The extension cable is too thin and/or too long.

• The mains voltage is lower than 230 V.

7. The machine is vibrating

• The machine has not been fastened onto the

workbench.

• The frame is not level with the oor.

• The saw blade has been damaged.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly clean

the machine housing with a soft cloth, preferably

after each use. Keep the ventilation slots free from

dust and dirt. If the dirt does not come off use a

soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water,

etc. These solvents may damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact your local Ferm dealer. In the back

of this manual you nd an exploded view showing

the parts that can be ordered.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material. Therefore please

make use of options for recycling the packaging.

Damaged and/or disposed of electrical

or electronic devices must be dropped

off at recycling stations intended for that

purpose.

Warranty

Read the warranty conditions on the separately

supplied warranty card.

The product and the user manual are subject to

change. Specications can be changed without

further notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1030 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info