Bedienungsanleitung Ferm TSM1032 (Seite 5 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

510129

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

8. Motor

9. Mains cable

10. Frame

11. Rip fence

12. Interlocking knob

13. Mitre guide

14. Nut

15. Screw

2. SAFETY INSTRUCTIONS

Explanation of symbols

Denotes risk of personal injury, loss of life or

damage to the tool in case of non-obser-

vance of the instructions in this manual.

Indicates the presence of an electrical

voltage.

Keep bystanders away.

Wear eye and ear protection.

Wear a dust mask protection.

Wear gloves when handling saw blades

and rough materials. Saw blades shall be

carried in a holder whenever practicable.

Before using the appliance

• Make sure that the saw bench is adequately

and effectively illuminated.

• When you use strip lighting you should be

aware of the so-called stroboscopic effect.

This may cause a rotating saw blade to appear

to be stationary. One solution is to use two

fittings in order to create

• phase displacement.

• Check the following points:

• Does the voltage of the motor and any fuse

employed correspond with the mains voltage?

Appliances with a voltage of 230 V~ may

be connected without problems to a mains

voltage of 220 V~.

• Are the feeder cable and plug in good condition:

sturdy, without loose bits or damage?

• Has the saw blade lost any teeth or is it

displaying cracks or fractures? If so, replace

the saw blade immediately.

• The protective hood may not be set higher

than required to let the workpiece pass.

• The riving knife should be narrower than the

saw cut and broader than the saw blade.

• Do not exercise lateral pressure on the saw

blade as it may cause it to break.

• Check the wood for knots, nails, cracks and

waste residues.

• These irregularities may cause the workpiece

to kick back dangerously.

• Ensure that no objects get into the extraction

system.

• These objects may come into contact with the

saw blades resulting in potentially hazardous

situations.

• Replace table insert when worn.

•

Rebating or grooving should not be carried out.

• Saws shall not be used for slotting (stopped

groove).

• Use only saw blades for which the maximum

possible speed is not less than the maximum

spindle speed of the tool and the material to be

cut.

• When transporting the machine use only

transportation devices and do never use

guards for handling or transportation.

• During transportation the upper part of the saw

blade should be covered by the guard.

Using the appliance

• Push the workpiece that you are going to saw

securely to the table surface.

•

Hold at the same time the section of the

workpiece that has been sawed to prevent it

breaking off. The hand that secures the sawed

section should remain behind the saw blade and

move away from it. Make sure that the hand that

you use to secure the workpiece does not cross

the hand that you use to operate the appliance.

•

Use the push stick supplied with the appliance.

• Use the push stick to guide smaller

workpieces past the saw blade.

• Do not use long extension cables.

• Allow the appliance to cool off before moving it.

• Do not remove wood residues in the vicinity of

the saw by hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1032 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TSM1032

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info