779800
31
Zoom out
Zoom in
Vorherige Seite
1/42
Nächste Seite
29
Operation
X. Operation
m WARNING! Risk of injury!
Improper assembly of the table saw can result in serious injury.
-Before start-up, assemble the table saw properly and completely.
-Before switching the table saw on, make sure the saw blade is correctly mounted and that
mobile parts can move freely.
After switching on the saw, you must wait until the saw blade (3) has reached the maximum
speed before you perform the cut.
Switching the table saw on and off (Fig. 1 / Pos. 8)
-To switch on the table saw, lift the cover flap (8) and press the green operating switch I. The
motor will start.
-To switch the table saw off, push the cover flap (8) to switch off.
Changing the speed (Fig. 1)
The table saw has 2 speed ranges:
To operate the saw at a speed of 3200 rpm (non-ferrous metals), set the speed switch (7) to
Slow-position.
To operate the saw at a speed of 5000 rpm (wood), set the speed switch (7) to Fast-position.
Sawing with the table saw
m WARNING! Risk of injury!
Improperly handling the table saw poses a risk of serious injury.
-When performing lengthwise cuts, do not stand directly in front of the table saw, instead
stand diagonal to the cutting line.
-When performing bevel cuts, always use the parallel guide.
-Use a push stick or a push block to safely push the workpiece by the saw blade. Immediately
replace a damaged or worn push stick.
-Secure long workpieces so that they do not tip over at the end of the cut. Use a roller stand
for this, for example.
-After switching on the table saw, wait until the saw blade has reached its maximum speed
before you perform the cut.
-Only operate the table saw with an extraction device.
-Each time after making a new setting, perform a test cut to check the set dimensions.
-Check and clean the suction channels regularly.
31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ferrex DX254TS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info