724612
24
Zoom out
Zoom in
Vorherige Seite
1/42
Nächste Seite
47.1cc Petrol Chainsaw
AFTER SALES SUPPORT
1300 889 028
(toll free)
e-mail: info.aldi@positecgroup.com
MODEL: №. 10084 • 08/2019 • FCS4800A
22
Checking the operation of the clutch.
Each time the chainsaw is started, the operation of the clutch (22) should
be checked as per the following detail. The chain MUST rst be checked to
ensure correct tension adjustment before starting.
1. When attempting to start the chainsaw, the chain (20) should not be trying
to move around the guide bar (19) under the inuence of the recoil starter
(11). If it is trying to rotate around the guide bar (19), STOP the starting
process and take the saw to an authorised service centre.
2. If point 1 is correct and the chain (20) is not trying to rotate around the
guide bar (19), start the chainsaw as per the section in the manual “Starting
the Chainsaw”.
3. With the chainsaw operating and at idle and ensuring the chain (20) is in
a safe position with respect of other persons and any objects, release the
chain brake (13).
CHECK, the chain (20) should NOT be rotating around the guide bar (19) at
idle speed.
4. Operate the safety lever (2) and then accelerate the throttle trigger (3).
The chain (20) should start and rotate. The harder the throttle trigger (3)
is pulled, the faster the chain (20) will rotate. RELEASE the throttle trigger
(3) so the motor returns to the idle condition. The chain (20) MUST stop
rotating around the guide bar (19) when the motor of the saw is at idle.
5. If the chain (20) is constantly rotating when the motor of the saw is at idle,
the chainsaw should NOT be used and the chainsaw should be taken to an
authorised service centre for repair.
6. DO NOT use the chainsaw if the clutch (22) does not totally disengage
when the motor of the saw is at idle.
Re-setting the Chain Brake
The front guard / chain brake (13) operates automatically in the event of
kickback. In the event of a kickback, the guide bar (19) kicks up, the wrist of
the operator’s hand on the top handle knocks against the front guard / chain
brake (13) causing it to move forward thus activating the chain brake (13).
To reset the front guard / chain brake (13) this can be done manually by
pulling it rmly towards the back of the chainsaw until a click is heard. (Fig A).
CAUTION: Each time the chainsaw is used, check that the chain brake (13)
is operating correctly.
Operation
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ferrex FCS4800A wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info