Bedienungsanleitung Festool AGC 18 (Seite 20 von 146) (Alle Sprachen)

778628

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

–Use special care when working corners,

sharp edges etc. Avoid bouncing and snag

ging the accessory. Corners, sharp edges

or bouncing have a tendency to snag the ro

tating accessory and cause loss of control

or kickback.

–Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades

create frequent kickback and loss of con

trol.

Safety warnings specific for Grinding and

Abrasive Cutting-Off Operations

–Use only wheel types that are recommen

ded for your power tool and the specific

guard designed for the selected wheel.

Wheels for which the power tool was not

designed cannot be adequately guarded

and are unsafe.

–The grinding surface of centre depressed

wheels must be mounted below the plane

of the guard lip. An improperly mounted

wheel that projects through the plane of

the guard lip cannot be adequately protec

ted.

–The guard must be securely attached to

the power tool and positioned for maxi

mum safety, so the least amount of wheel

is exposed towards the operator. The

guard helps to protect the operator from

broken wheel fragments, accidental con

tact with wheel and sparks that could ignite

clothing.

–Wheels must be used only for recommen

ded applications. For example: do not

grind with the side of cut-off wheel. Abra

sive cut-off wheels are intended for periph

eral grinding, side forces applied to these

wheels may cause them to shatter.

–Always use undamaged wheel flanges that

are of correct size and shape for your se

lected wheel. Proper wheel flanges sup

port the wheel thus reducing the possibility

of wheel breakage. Flanges for cut-off

wheels may be different from grinding

wheel flanges.

–Do not use worn down wheels from larger

power tools. Wheel intended for larger

power tool is not suitable for the higher

speed of a smaller tool and may burst.

Additional safety warnings specific for Abra

sive Cutting-Off Operations

–Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt to

make an excessive depth of cut. Over

stressing the wheel increases the loading

and susceptibility to twisting or binding of

the wheel in the cut and the possibility of

kickback or wheel breakage.

–Do not position your body in line with and

behind the rotating wheel. When the

wheel, at the point of operation, is moving

away from your body, the possible kickback

may propel the spinning wheel and the

power tool directly at you.

–When wheel is binding or when interrupt

ing a cut for any reason, switch off the

power tool and hold the power tool mo

tionless until the wheel comes to a com

plete stop. Never attempt to remove the

cut-off wheel from the cut while the wheel

is in motion otherwise kickback may oc

cur. Investigate and take corrective action

to eliminate the cause of wheel binding.

–Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully re-enter the cut. The wheel

may bind, walk up or kickback if the power

tool is restarted in the workpiece.

–Support panels or any oversized work

piece to minimize the risk of wheel pinch

ing and kickback. Large workpieces tend to

sag under their own weight. Supports must

be placed under the workpiece near the

line of cut and near the edge of the work

piece on both sides of the wheel.

–Use extra caution when making a “pocket

cut” into existing walls or other blind

areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects

that can cause kickback.

Safety Warnings Specific for Wire Brushing

Operations

–Be aware that wire bristles are thrown by

the brush even during ordinary operation.

Do not overstress the wires by applying

excessive load to the brush. The wire bris

tles can easily penetrate light clothing

and/or skin.

–If the use of a guard is recommended for

wire brushing, do not allow any interfer

ence of the wire wheel or brush with the

guard. Wire wheel or brush may expand in

diameter due to work load and centrifugal

forces.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool AGC 18 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info