Bedienungsanleitung Festool AXT 50 LA (Seite 13 von 70) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

497616

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

3 Power supply and start-up

The mains voltage must correspond to

the speciﬁ cation on the rating plate.

To momentarily perform work within the overload

range, a fuse of at least 10 amps is required for a

230 V power supply.

Switch (1.5) serves as an On/Off switch (press =

ON, release = OFF).

Sliding the button (1.4) forwards releases the

plunge-cut lock. The saw can now be adjusted to

the preset cutting depth.

When the machine is lifted, the sawing unit

springs back into the starting position.

4 Machine settings

Always remove the power supply plug

from the socket before carrying out any

work on the machine.

4.1 Cutting depth

The cutting depth can be set at 0 – 47 mm:

- Open the rotary knob (1.1).

- Set the stop (1.3) to the required cutting depth

while reading the scale,

- tighten rotary knob (1.1).

4.2 Cutting angle

The sawing unit can be swivelled between 0° and

45°:

- Unscrew the brush ring (3.2),

- Loosen the front and rear clamps (1.8, 3.6),

- Set to the required cutting angle while reading

the scale (3.5),

- Close both clamps (1.8, 3.6) once more.

4.3 Changing the saw blade

Only Festool saw blades (435450) should

be ﬁ tted to the AXT 50 LA. The use of other

saw blades is not permitted.

The cutting geometry of the saw blade (435450)

has been adapted to meet special requirements

for cutting ﬁ bre cement panels and similar ma-

terials. When sharpening blades, remember that

the teeth should have a special cutting angle.

Procedure

- Loosen screw (3.8) with Allen key (1.6),

- Remove the dust extraction hood (3.1) up-

wards,

- Set the cutting depth to approx. 15 mm and push

down the machine until the stop is reached,

- Insert the pins supplied into the two holes (3.3)

on the clamping ﬂ ange,

- Unscrew the bolt (3.4) using the Allen key

(1.6),

- Remove saw blade,

- Clean ﬂ ange,

- Insert new saw blade. Warning: The direction of

rotation of the saw blade and the machine must

be the same.

- Tighten screw (3.4),

- Attach the dust extraction hood (3.1) once

again.

4.4 Dust extraction

Always connect the machine to a dust

extractor.

You can connect a Festool extractor with an ex-

tractor hose diameter of 36 mm to the extractor

connector (1.2).

The brush ring (3.2) ﬁ lls the gap between the

machine and the workpiece and enhances the

efﬁ ciency of the extractor.

5 Working with the machine

Always secure the workpiece in such a

manner that it cannot move while being

sawed.

The machine must always be held with

both hands by the designated handles.

Always push the machine forwards, never

pull the machine backwards towards

you.

Only guide the machine against the work-

piece when it is switched on.

You should also wear a dust mask for

work which produces dust.

Sawing with a guide rail

Fitting an AUP Festool saw guide makes saw guid-

ance easier and safer and ensures more accurate,

cleaner cuts.

The AUP saw guide is available in two lengths:

AUP 1750 mm Order no. 482543

AUP 3000 mm Order no. 482545

Working procedure

- Place the guide rail on the workpiece and align

it along the relevant cutting line.

- Use two clamps to secure the guide rail to the

workpiece and prevent it from slipping.

- Place the machine on the guide rail. Depending

on the cutting angle, the machine is slotted ei-

ther into the inner guide groove (2.1) for 90° cuts

or the outer guide groove (2.2) for 45° cuts.

- Switch on the machine (1.5).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool AXT 50 LA Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info