Bedienungsanleitung Festool Basis KA 200 (Seite 5 von 22) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

499882

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

1 Trimming attachment

The trimming attachment consists of a base support

(1.1) and a stop ruler with the following main parts:

profile rail (1.4),

extending end piece (1.3)

with tape measure (1.2),

adjustable intermediary piece (1.10),

adjustable stop (1.5),

tape measure clamp (1.7)

and workpiece support (1.6).

2 Assembly of the stop ruler

2.1 Fastening to mitre fence (Fig. 1)

The stop ruler is fastened to the mitre fence (1.8) of

your BASIS 1 A.

Remove the profile rail of the BASIS 1 A from the

mitre fence and replace with the profile rail (1.4) of

the stop ruler.

Insert the tape measure with holder (1.12) into the

end piece and pull the tape measure through the

upper groove (1.13) of the end piece, intermediary

piece and profile rail.

2.2 Adjusting the stop ruler (Fig. 2)

To prevent the tape measure from making contact

with the saw blade, this starts at 30 mm.

The gap between the front edge of the profile rail

and the rim of the saw blade thus has to be adjusted

to 30 mm as follows: pull the tape measure (2.1)

30 mm over the end of the profile rail (2.2) and fix

with the tape measure clamp (2.3).

Set the mitre fence to a right-angled cut and push

the profile rail until the end of the tape measure

touches the sides of the saw blade cutting edges

(2.4).

Clamp the profile rail tight with the rotary knob (2.5)

and lock the tape measure so that its end is flush

with the front edge of the profile rail.

The tape measure now shows the exact gap to the

saw blade.

2.3 Fastening the workpiece support (Fig. 3)

The workpiece support is used to support longer

workpieces.

Screw the workpiece support to the lower groove

of the profile rail by its slit (3.1) using the rotary

knob (3.2) and the feather key (3.3) so that the two

cams (3.5) engage in the groove.

2.4 Moving the stop ruler

Loosen the rotary knob (1.9) to extend and retract

the end piece (1.3).

The maximum cutting range is 2050 mm.

3 Assembly of the base support (Fig. 4)

The base support supports the stop ruler.

To assemble release the two rotary knobs (4.1) on

the workpiece support (4.8) until the two additional

legs (4.3) can be inserted into the pipe clamp (4.4).

Insert the additional legs until the base support is

the same height as your BASIS 1 A and then tighten

the additional legs with the rotary knobs (4.1).

Screw the fastening plate to the lower groove of the

stop ruler by its slit (4.5) using the rotary knob (4.2)

and the feather key (4.7) so that the two cams (4.6)

engage in the groove.

4 Adjustable stop (Fig. 5, Order No. 488 560)

4.1 Fitting the adjustable stop

Open the clamp for the adjustable stop with the

rotary knob (5.1) until the clamping piece (5.5) can

be inserted into the upper groove (3.4) of the profile

rail or the adjustable intermediary piece.

Fix the adjustable stop by tightening the rotary knob.

4.2 Setting the adjustable stop

The adjustable stop can be set with no play in the

groove with the two screws (5.6).

Fit the adjustable stop and tighten the two screws

until this can be moved with no play, but still easily,

in the groove.

4.3 Moving the stop plate

You can mount the stop plate (5.3) on the other

side of the adjustable stop if required with the screw

(5.4).

The adjustable stop can be fitted to the profile rail

of the BASIS 1 As mitre fence.

The stop plate (5.3) must be fastened to the

adjustable stop with the screw (5.4) through the

bore hole (5.2).

Make sure that the nut (5.7) with washer is always

on the side opposite the stop plate.

5 Fitting on right side

When you purchase the unit, the trimming attachment

is assembled so that it can be fitted on the left side

of your BASIS 1 A.

If you wish to fit it on the right side, it can be

dismantled by releasing the screw (1.11) and

removing the rotary knob (1.9) for laterally inverted

installation.

There are bore holes for the screw (1.10) and rotary

knob (1.9) on both ends of the adjustable stop

(1.4) and end piece (1.3) for this purpose.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool Basis KA 200 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info