778617
16
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
70–100%
40–70%
15–40%
< 15%*
* Recommendation: Charge the battery pack
before any further use.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
8 Settings
CAUTION
Risk of injury
Only adjust the settings when the power
tool is switched off.
8.1 Changing direction of rotation [1-8]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rota
tion
8.2 Changing gear [1-4]
Only actuate the gear switch with the tool
switched off. Otherwise there is a risk of
damaging the gear unit.
Gear switch forwards (digit 1 visible) =
1st gear
Gear switch to rear (digit 2 visible) =
2nd gear
8.3 Fastening
Adjust the switch so that its marking [1-7]
faces the screw symbol [1-6].
Adjust the torque accordingly at the torque
wheel [1-1].
Position 1 = low torque
Position 25 = high torque
An acoustic signal sounds when the preset tor
que is reached and the machine then switches
off. You must release and press the ON/OFF
switch [1-9] again to start the machine.
8.4 Drilling
Adjust the switch [1-7] so that its marking
faces the drilling symbol [1-5]. Maximum tor
que is set in this position.
9 Tool holder, attachments
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
9.1 CENTROTEC tool chuck [3]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CEN
TROTEC tool chucks.
9.2 Chuck [4]
For clamping drill bits and bits with max. shaft
diameter of 13 mm.
WARNING! Clamp the tool centrally in the
chuck.
9.3 Angle attachment [5]
Drilling and screwdriving at right angles to the
power tool (available as an accessory depend
ing on the model).
9.4 Eccentric adapter [6]
Screwdriving close to edges with bits according
to ISO 1173 (available as an accessory depend
ing on the model).
9.5 Tool holder in the drill spindle [7]
Bits can be inserted directly into the hexagon
socket holder of the drill spindle.
10 Working with the machine
WARNING
Risk of injury
Always secure the workpiece in such a
manner that it cannot move while being
machined.
10.1 Bit depot [1-2]
Magnetic, for storing bits and bit holders.
10.2 Acoustic warning signals
Acoustic warning signals sound and the ma
chine switches off in the following operating
states:
English
16
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool C 18 Li wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Festool C 18 Li

Festool C 18 Li Zusatzinformation - Alle Sprachen - 38 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info