Bedienungsanleitung Festool CARVEX PSB 420 EBQ (Seite 17 von 114) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

778601

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

–Harmful/poisonous dust may be produced

when working (e.g. paint products con

taining lead and some types of wood).

Contact with or inhalation of this dust may

pose a risk for the operating personnel or

persons in the vicinity. Comply with the

safety regulations that apply in your coun

try. Connect the power tool to a suitable

dust extractor.

– Always connect the machine to a dust ex

tractor when performing work that gener

ates dust.

– Check the plug and the cable regularly and

should either become damaged, in order to

avoid a hazard, have them replaced by an

authorised after-sales service workshop.

–Stroboscopic light can cause epileptic

seizures. Do not use this machine if you

are susceptible to epileptic seizures.

– Do not look into the stroboscope light.

Looking into the light source can damage

your vision.

–Only for AS/NZS: The tool shall always be

supplied via residual current device with a

rated residual current of 30 mA or less.

2.3 Metal processing

When processing metal, the following

measures must be taken for safety rea

sons:

– Install an upstream residual-current circuit

breaker (RCD, PRCD).

– Connect the machine to a suitable dust ex

tractor.

– Regularly remove dust deposits from the

motor housing.

– Use a metal saw blade.

– Close the chip guard.

Wear protective goggles.

2.4 Emission levels

The levels determined in accordance with

EN 62841 are typically:

PS 420 EBQ

Sound pressure level LPA = 87 dB(A)

Sound power level LWA = 98 dB(A)

Uncertainty K = 5 dB

PSB 420 EBQ

Sound pressure level LPA = 86 dB(A)

Sound power level LWA = 97 dB(A)

Uncertainty K = 5 dB

CAUTION

Noise generated when working

Risk of damage to hearing

► Use ear protection.

Vibration emission level ah (vector sum for

three directions) and uncertainty K measured in

accordance with EN 62841:

PS 420 EBQ PSB 420 EBQ

Sawing wood ah8.0 m/s28.5 m/s2

Sawing metal ah6.5 m/s25.5 m/s2

Uncertainty K 1.5 m/s21.5 m/s2

The specified emission levels (vibration, noise)

– are used to compare machines.

– They are also used for making preliminary

estimates regarding vibration and noise

load during operation.

– They represent the primary applications of

the power tool.

CAUTION

The emission values may deviate from the

specified values. This is dependent on how

the tool is used and the type of workpiece

being machined.

► The actual load during the entire operating

cycle must be evaluated.

► Depending on the actual load, suitable pro

tective measures must be defined in order

to protect the operator.

3 Intended use

Jigsaws are designed for sawing wood and ma

terials similar to wood. With the special saw

blades offered by Festool, these machines can

also be used for sawing plastic, steel, alumini

um, non-ferrous metal and ceramic plates.

The user is liable for improper or non-in

tended use.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CARVEX PSB 420 EBQ Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info