Bedienungsanleitung Festool CS 50 EB Floor (Seite 17 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498002

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

- Deformed or cracked saw blades and saw

blades with blunt or broken cutting edges

must not be used.

- Transport and store the tools in a suitable re-

ceptacle;

- Only use the machine if all safety devices are in

their correct positions, the machine is in good

condition and has been well maintained.

- Replace a worn or damaged (e.g. bedded in)

tabletop immediately.

- Operating personnel must have received ade-

quate training in the use, set-up and operation

of the machine.

- Faults on the machine, including the separat-

ing guards or the tool, must be reported to

maintenance staff immediately upon discov-

ery. The machine must not be used until the

fault has been eliminated.

Wear suitable personal protec-

tive equipment: ear protection

to reduce the risk of hearing

loss, safety goggles, a dust

mask to prevent inhalation of

harmful dust, protective gloves

when working with raw materials and when

changing tools.

- To minimise noise, the tool must be sharpened

and all noise reducing elements (covers etc.)

must be properly adjusted.

- When cutting wood, connect the machine to a

dust extractor corresponding to EN 60335-2-

69, dust category M.

- To minimise the creation of dust, the machine

is to be connected to a suitable dust extractor,

and all the elements for dust collection (ex-

tractor hood etc.) must be properly set.

- Never process material containing asbestos.

- Make sure that there is adequate lighting in

the room or workplace.

- Always assume the correct position before

starting work:

- front at the operating end,

- facing the machine,

- next to the cutting line.

- Use the accompanying workpiece holder to

guide the workpiece accurately past the saw

blade.

- Use the accompanying spacer wedge and pro-

tective cover. Make sure the cover is set as de-

scribed in the operating instructions.

- Use a suitable device to support long work-

pieces and ensure that they are horizontal.

- Pull the plug from the main power socket be-

fore changing tools and rectifying faults such

as removing trapped splinters.

- Do not remove offcuts or other workpiece parts

from the cutting area while the tool is still run-

ning and until the saw blade stops.

- If the saw blade is blocked, switch the machine

off immediately and disconnect the mains

plug. Do not remove the jammed workpiece

until you have done this.

- Cutting rebates or grooves is only permitted

with a suitable protective device ﬁ tted, e.g. a

protective tunnel over the saw table.

- Do not use circular saws for cutting slots

(grooves in workpiece).

- Before transporting the machine, make sure

that the top protective guard covers the top

section of the saw blade.

- Do not use the top protective cover as a handle

for transportation!

- When not in use, store the push stick in the

holder provided on the machine.

3.3 Noise and vibration information

Sound pressure level

Idling / processing 84 / 90 dB(A)

Noise power level

Idling / processing 97 / 103 dB(A)

Measurement tolerance K = 3 dB

Wear ear protection!

Measured acceleration < 2.5 m/s²

The emission values speciﬁ ed (vibration, noise)

were measured in accordance with the test con-

ditions stipulated in EN 61029 and are intended

for machine comparisons. They are also used for

making preliminary estimates regarding vibration

and noise loads during operation.

The emission values speciﬁ ed refer to the main

applications for which the power tool is used. If

the electric power tool is used for other applica-

tions, with other tools or is not maintained suf-

ﬁ ciently prior to operation, however, the vibration

and noise load may be higher when the tool is

used. Take into account any machine idling times

and downtimes to estimate these values more

accurately for a speciﬁ ed time period. This may

signiﬁ cantly reduce the load during the machine

operating period.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CS 50 EB Floor Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info