778794
19
Zoom out
Zoom in
Vorherige Seite
1/113
Nächste Seite
6 Operation
WARNING
Unauthorised voltage or frequency!
Risk of accident
The mains voltage and the frequency of the
power source must correspond with the
specifications on the machine's name
plate.
In North America, only Festool machines
with the voltage specifications 120 V/60 Hz
may be used.
6.1 Initial operation
Open the locking clips [2-2] and remove the
top section of the machine [2-1].
Remove the accessories from the dust con
tainer [2-3] and the packaging!
Insert a filter bag in the dust container that
fulfils statutory requirements (see chap
ter 7.8).
Replace the top section [2-1] and close the
locking clips [2-2].
Attach the cable holder to the rear of the
mobile dust extractor (see Fig. [3]).
Insert the sealing plug [1-1] on the panel
(see Fig. [1] ).
Connect suction hose at the extractor open
ing [1-2].
6.2 Switch on/off
Insert the plug into an earthed socket.
The use of extension cables in Zone 22 is
not permitted.
CAUTION
Risk of injury from tools starting up unex
pectedly
Before setting the switch to the "AUTO" or
"MAN" position, make sure that the con
nected tool is switched off.
The switch [1-9] serves as an on/off switch.
Switch position "0"
Appliance socket [1-11] is disconnected from
the power, mobile dust extractor is switched
off.
"MAN" switch position
Appliance socket [1-11] is connected to the
power, the mobile dust extractor starts.
"Auto" switch position
Appliance socket [1-11] is connected to the
power, the mobile dust extractor starts when
the connected tool is switched on.
7 Settings
7.1 Adjusting the hose diameter
Adjust the hose diameter adjuster [1-8] to
match the diameter of the connected hose.
This ensures that the air speed in the ex
tractor hose is measured correctly (see
section "Volumetric flow monitoring").
7.2 Connecting electric power tools
WARNING
Risk of explosion, risk of injury
Do not use the appliance's socket in zone
22.
Observe the maximum appliance socket
connected load (see chapter "Technical da
ta")
Switch off the electric power tool.
Connect the electric power tool to the appli
ance socket [1-11].
7.3 Connecting pneumatic tools
WARNING
Risk of injury
Switch off the air tool.
With the compressed air module [1-3], the au
tomatic switch-on function for the mobile dust
extractor also works in conjunction with air
tools.
We also recommend installing the VE service
unit (495886). The service unit filters and lubri
cates the compressed air and enables an ad
justment of the air pressure. An IAS adapter
(454757) is available to connect Festool air tools
to the IAS system.
The operating pressure of the tool must be 6
bar for the automatic switch-on unit to function
correctly.
7.4 Connecting the energy box
The connection for the energy box (EAA) [1-4]
allows you to connect the mobile dust extractor
with the EAA in order to couple the automatic
switch-on unit on the mobile dust extractor with
the equivalent unit on the EAA.
7.5 Adjusting the suction power
at the rotary knob [1-10].
English
19
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool CTL 48 E LE EC-B22 R1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info