778794
20
Zoom out
Zoom in
Vorherige Seite
1/113
Nächste Seite
7.6 Applying the brake
Folding out the black brake lever [1-15] pre
vents the mobile dust extractor from rolling. To
achieve this, lift the front end of the mobile dust
extractor slightly and push the black brake lev
er downwards until it latches into place. Push
the green lever [1-14] to release.
7.7 Temperature cut-out
A temperature cut-out switches the mobile dust
extractor off when it reaches a critical tempera
ture to prevent overheating.
A temperature cut-out switches the mobile
dust extractor off when it reaches a critical
temperature to prevent overheating.
Switch off the mobile dust extractor and al
low to cool for approx. 5 minutes.
Change the cooling air filter if necessary
(see chapter 9.2).
If the mobile dust extractor will not switch
on again, please contact a Festool service
workshop.
7.8 Changing the filter bag (SC-FIS-CT 48)
Removing the filter bag [4]
Open the locking clips [2-2] and remove the
top section of the machine [2-1].
Remove the filter bag.
Dispose of the used filter bag in accordance
with statutory regulations.
Inserting the filter bag [5]
Insert a new filter bag (SC-FIS-CT 48) in the
inlet port of the dust container and interlock
it. Important: be aware that the locking en
gages.
Make sure that the filter bag is not pinched
between the top and bottom sections.
Replace the top section [2-1] and close the
locking clips [2-2].
7.9 Volumetric flow monitoring
An acoustic warning signal sounds if the air
speed in the suction hose falls below 20 m/s.
Possible causes Solution
Value set on the suction power adjust
er [1-10] is too low. Set the suction power adjuster to a higher value (see
Chapter 7.5).
Rotary knob [1-8] not set to the correct
hose diameter. Set the knob to the correct hose diameter (see Chap
ter 7.1).
Suction hose blocked or kinked. Remove blockage or kink.
Filter bag full. Insert a new filter bag (see Chapter 7.8).
Dirty main filter. Changing the main filter (see Chapter 9.1).
Monitoring electronics malfunction. Send to a Festool service workshop for repair.
Wet extraction. Functional reliability not affected, no actions re
quired.
8 Working
8.1 Handling
SysDoc SYSTAINER attachment system: A
SYSTAINER can be attached to the storage area
using the four locking latches [6-1].
8.2 Extracting dry materials
CAUTION
Hazardous dust
Damage to the respiratory passage
Always use a filter bag when extracting
hazardous materials!
Do not use the machine if the volumetric
flow monitoring function is inactive.
Observe the following when extracting dust
generated by operating electric power tools:
If the exhaust air is discharged back into the
room, the air renewal rate L within the room
must be sufficient. The volume of air dis
charged back into the room must not exceed
50% of the fresh air volume flow (room volume
VR x air renewal rate LW). Observe all the rele
vant regional regulations.
Remember: A moist main filter clogs more
quickly when extracting dry materials. There
fore, dry the main filter before extracting dust
or replace the damp filter with a dry one.
English
20
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool CTL 48 E LE EC-B22 R1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info