Bedienungsanleitung Festool CTL MINI 1800W (Seite 12 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

574990

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

CTL MINI/MIDI

"MAN" switch position

Appliance socket

[1-2]

is connected to the power, the

mobile dust extractor starts.

"Auto" switch position

Appliance socket

[1-2]

is connected to the power, the

mobile dust extractor starts when the connected tool

is switched on.



Insert the plug into an earthed socket.

Pull the plug from the socket when the ma-

chine is not in use and prior to maintenance

and cleaning work.

6.2 Connecting electric power tools



Connect the electric power tool to the appliance

socket

[1-2]

6.3 Connecting the suction hose [1A]



Connect the suction hose to the angle adapter

[1-

on the extraction opening

[1-5]

7Settings

7.1 Adjusting the suction power



Use the rotary knob

[1-1]

7.2 Applying the brake [1B]



Raise the front of the dust extractor slightly.



Push down the brake

[1-13]

until it engages into

position.



Actuate the lever

[1-12]

to release.

7.3 Temperature cut-out

A temperature cut-out switches the mobile dust ex-

tractor off when it reaches a critical temperature to

prevent overheating.



Switch off the mobile dust extractor, allow to cool

for about 5 minutes then switch on again.



Not possible to switch on: contact Festool service

workshop.

7.4 SYSDOC

A Systainer can be secured to the storage area

[1-7]

using the T-LOC latch

[1-8]

. Systainers without a T-

LOC can be secured using four SysDoc latches

[1-3]

8Working

8.1 Extracting dry materials

When extracting dust that exceeds the per-

mitted limit values, only extract from a single

machine (electric or air tool).

Observe

the following when extracting dust gener-

ated by operating electric power tools:

Ensure there is adequate ventilation! Observe re-

gional regulations!

Limit values:

exhaust air max. 50% of the clear air

volume

Formula:

room volume V

x air renewal rate L

8.2 Extracting wet materials/liquids

Remove the filter bag!

Recommendation:

use a special wet filter.

The dust extractor stops automatically when the

maximum level is reached.

After wet extraction, allow the main filter to dry!

8.3 After finishing work



Switch off the mobile dust extractor and pull out

the mains plug.



Wind up the mains power cable.



Empty the dirt trap.



Place the suction hose

[2-1]

and mains power ca-

ble

[2-2]

in the top section. Insert the mains cable

through the recess

[2-3]



Vacuum and wipe off the inside and outside of the

mobile dust extractor.



Place the mobile dust extractor in a dry room in-

accessible to unauthorised users.

WARNING

Risk of injury



Observe the maximum appliance socket con-

nected load (see chapter "Technical data")



Switch off the electric power tool.

CAUTION

Hazardous dust

Damage to the respiratory passage



Always use a filter bag!

CAUTION

Escaping foam and fluids



Switch off and empty the machine immediately.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CTL MINI 1800W Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info