796187
22
Zoom out
Zoom in
Vorherige Seite
1/145
Nächste Seite
7 Battery pack
Before using the battery pack, check that the
battery interface is clean. Any contamination of
the battery interface may impair correct contact
and lead to the contacts being damaged.
A faulty contact may result in the machine over
heating or being damaged.
[2a] Remove the battery pack.
[2b]
klick
Insert the battery pack – until it
clicks into place.
The cordless mobile dust extractor can
only be operated with two battery packs.
Compatible battery packs (see section 4).
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
8 Commissioning
Standby mode
Press the on/off button [1-14].
The green LEDs on the status display [1-12] in
dicate standby mode.
Pressing the on/off button again will switch off
the cordless mobile dust extractor.
Starting/stopping the cordless mobile dust
extractor manually
The cordless mobile dust extractor is in standby
mode.
Directly on the cordless mobile dust extractor:
Press the MAN button [1-13] to start/stop.
Alternatively, use the connected remote control
CT-F I (see chapter 9.2):
Press the MAN button [1-18] on the remote
control to start/stop.
Starting/stopping the cordless mobile dust ex
tractor automatically
The cordless mobile dust extractor is in standby
mode.
To start/stop the cordless mobile dust ex
tractor automatically: Switch the connected
battery-powered power tool on/off (see
chapter 9.1).
9 Connecting a device
WARNING
Risk of injury from a cordless mobile dust
extractor starting up unsupervised
Before performing any work with the cord
less mobile dust extractor, check which re
mote control and which cordless power
tool are connected to the cordless mobile
dust extractor.
A battery-powered power tool must always
be connected to the cordless mobile dust
extractor via the suction hose. After finish
ing work, the connection to the cordless
mobile dust extractor must be disconnec
ted.
The remote control must only be attached
to the suction hose.
9.1 Connecting a battery-powered power
tool
In standby mode, press the connection but
ton [1-9].
The connection display [1-10] slowly flashes
blue. For a period of 60 seconds, the cordless
mobile dust extractor is ready for connection.
Switch on the power tool.
The cordless mobile dust extractor starts up.
The cordless mobile dust extractor is connec
ted until the on/off button [1-14] is pressed or a
battery pack is removed (from the cordless mo
bile dust extractor). The power tool must then
be connected again.
Connecting a new power tool overwrites
the previous connection.
This function is only possible on Festool
power tools with a Bluetooth® battery
pack.
9.2 Connecting the CT-F I remote control
To be able to connect a remote control to a
cordless mobile dust extractor, the remote con
trol must be reset (see "Reset on the remote
control").
Remote controls that have not been connected
previously can be connected directly.
A connection that has been created be
tween remote controls and the cordless
mobile dust extractor will persist even af
ter pressing the on/off button or removing
a battery pack (from the cordless mobile
dust extractor).
English
22
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool CTLC SYS I wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info